You are here
Active forum topics
Primary tabs
Topic |
Replies | Last post | Forum | |
|---|---|---|---|---|
|
ESC for Prop noise testing by Raam Sundhar on Thu, 2020-09-17 11:03 |
1 |
by frank Tue, 2020-09-22 09:00 |
General discussion | |
|
Esc does not reply by nemethLali on Sun, 2021-08-01 16:07 |
1 |
by nemethLali Fri, 2021-08-06 22:18 |
Third Party Hardware | |
|
ESC ceases operation after 40 sec ride by dekafive on Sun, 2019-08-25 22:25 |
1 |
by frank Mon, 2019-09-02 10:50 |
Third Party Hardware | |
|
esc burning my motor by renaudbarbier on Tue, 2023-02-28 09:38 |
by renaudbarbier Tue, 2023-02-28 17:18 |
General discussion | ||
|
ESC blinks red when I give it input by menghaitang on Tue, 2021-03-02 21:22 |
1 |
by Knapers Wed, 2021-03-03 16:57 |
General discussion | |
|
Error on log-file recording: Could not get Positioning Working by hpb66 on Mon, 2022-05-23 08:23 |
by hpb66 Mon, 2022-05-23 08:23 |
VESC Tool | ||
|
error message binding loop detected for property ! wtf by georg65 on Sat, 2024-09-28 08:49 |
by georg65 Tue, 2024-10-01 03:04 |
General discussion | ||
|
Error message by DAVCRO on Thu, 2023-03-09 17:15 |
1 |
by Gos1 Wed, 2023-07-05 13:17 |
Projects incorporating VESC technology | |
|
error firmware BMS by Sebastiangeitne... on Mon, 2022-08-15 21:36 |
1 |
by Sebastiangeitne... Thu, 2022-08-18 12:26 |
VESC Firmware | |
|
Error creating appimage by EduardoHP28 on Fri, 2025-02-21 07:35 |
by EduardoHP28 Fri, 2025-02-21 07:37 |
VESC Tool | ||
|
Error code 6 by PatWhite32 on Mon, 2023-06-19 23:15 |
by PatWhite32 Mon, 2023-06-19 23:15 |
General discussion | ||
|
Error 500 on older private messages by TechAUmNu on Wed, 2018-05-09 23:15 |
3 |
by Roger Wolff Mon, 2018-05-14 10:06 |
General discussion | |
|
Erratic braking on vesc using large hub motor. by jtechbop on Sun, 2021-09-19 06:54 |
2 |
by jtechbop Tue, 2021-10-19 20:59 |
General discussion | |
|
ERPM, the RPM on the motor does not change by hopeingod on Fri, 2024-05-10 11:15 |
6 |
by hopeingod Mon, 2024-05-13 20:45 |
VESC Tool | |
|
ERPM to Rpm by faheemift on Wed, 2021-03-31 11:11 |
9 |
by faheemift Wed, 2021-04-14 13:01 |
General discussion | |
|
ERPM settings restrict carving speed on outer wheel. Poor user experience. by Paul15578 on Fri, 2018-01-12 02:28 |
9 |
by Ackmaniac Tue, 2018-04-24 13:47 |
General discussion | |
|
ERPM scaling / Maximum motor speed / RPM by Azza on Tue, 2019-09-03 17:16 |
1 |
by Azza Fri, 2019-09-06 18:20 |
VESC Tool | |
|
Erpm output via pwm by Flyingtux on Tue, 2021-09-14 20:34 |
2 |
by lurch Fri, 2021-10-29 14:09 |
General discussion | |
|
eRPM limited to 40600 or so on 6.6 by Dan Slanker on Fri, 2021-04-16 01:22 |
4 |
by TechAUmNu Mon, 2021-04-19 11:10 |
General discussion | |
|
ERPM Limit Update Over CAN by josh on Sun, 2019-06-02 01:48 |
1 |
by josh Sun, 2019-06-02 02:05 |
Feature Requests |
Pages
