You are here
Active forum topics
Primary tabs
Topic |
Replies | Last post | Forum | |
|---|---|---|---|---|
|
Can I re-use an old Galaxy S3 to run the VESC tool? by Munkyheed on Fri, 2019-08-02 20:00 |
by Munkyheed Fri, 2019-08-02 20:00 |
VESC Tool | ||
|
Can I use 12V power supply? by ryde6 on Sun, 2021-04-25 08:19 |
2 |
by vadicus Wed, 2021-07-14 21:01 |
General discussion | |
|
Can larger BLDC motors be controlled with VESC? by Heimfried on Sun, 2020-02-02 21:29 |
3 |
by Heimfried Thu, 2020-02-06 22:39 |
General discussion | |
|
Can motor parameters be detected with shaft load? by powerlabor001 on Thu, 2018-03-15 13:24 |
4 |
by powerlabor001 Sat, 2018-03-24 03:07 |
General discussion | |
|
Can not adjust the RPM on my 1350 w motor by Arne Norway on Wed, 2019-01-09 18:47 |
6 |
by sam.vanratt Sun, 2019-01-13 13:36 |
General discussion | |
|
Can not run again after run perfectly !! Pls help by Streetstar69 on Tue, 2021-11-23 03:03 |
1 |
by frank Tue, 2021-11-23 10:03 |
General discussion | |
|
can not start motor with high duty by qdxiatao on Sat, 2018-03-24 03:58 |
by qdxiatao Sat, 2018-03-24 03:58 |
General discussion | ||
|
Can not update firmware on FLIPSKY 4.12, still af 3.4 (att. newbie) by SlinBin on Wed, 2019-03-27 21:59 |
11 |
by thewho Thu, 2020-07-16 18:06 |
Third Party Hardware | |
|
CAN not working on VESC MkV by chundri on Tue, 2021-01-12 15:06 |
1 |
by chundri Wed, 2021-01-13 15:48 |
VESC Original Hardware | |
|
CAN sends error frame by dgarciasoto on Wed, 2022-04-27 07:11 |
by dgarciasoto Wed, 2022-04-27 07:11 |
VESC Firmware | ||
|
Can someone help me understand why I've burned up a DRV8302 in less than 10 seconds? by shimdidly on Fri, 2017-10-13 02:01 |
3 |
by shimdidly Mon, 2017-10-16 17:13 |
General discussion | |
|
Can someone please post the steps to do position control from vesc tool? by dp on Wed, 2022-02-16 14:51 |
1 |
by frank Wed, 2022-02-16 17:24 |
General discussion | |
|
Can someone verify this by jsbenson on Mon, 2023-06-26 09:22 |
by jsbenson Tue, 2023-06-27 07:50 |
General discussion | ||
|
CAN STATUS INTERRUPTS MOTOR OUTPUT by v1n23nt on Tue, 2022-03-15 09:06 |
by v1n23nt Tue, 2022-03-15 09:10 |
General discussion | ||
|
Can the PPM mapping be changed so that higher duty cycle means slower speed? by UncleJoe on Mon, 2020-05-25 11:46 |
3 |
by UncleJoe Thu, 2020-11-19 15:06 |
VESC Tool | |
|
Can VESC be in parallel connection with BMS while being charged? by dfelz on Tue, 2020-06-16 21:47 |
1 |
by TheFallen Wed, 2020-06-17 16:03 |
General discussion | |
|
Can you flash VESC Hardware with BLheli firmware? by saliraza.ai on Fri, 2021-02-26 20:38 |
1 |
by TheFallen Mon, 2021-03-01 16:31 |
VESC Original Hardware | |
|
Can you switch censored to sensor less or HFI by diyRick on Wed, 2021-06-30 23:43 |
2 |
by drdrs Wed, 2021-07-07 07:11 |
General discussion | |
|
Can you use both axes on a 2-axis nunchuck/joystick controller with VESC? by adamdorr on Tue, 2019-12-31 22:05 |
6 |
by sanketh1691 Sat, 2021-10-09 00:45 |
General discussion | |
|
Can't ajust braking torgue with Plettenberg Predator 30/8 by VescBuilder on Sun, 2017-11-12 16:13 |
6 |
by benjamin Thu, 2017-11-23 09:38 |
Third Party Hardware |
Pages
