You are here

Active forum topics

Topicsort descending Replies Last post Forum
Normal topic CAN bus rate, Flipsky Mini FSESC6.7
by christian.lees on Tue, 2022-01-18 22:57
by christian.lees
Tue, 2022-01-18 22:57
General discussion
Hot topic CAN bus support not enabled in this build of vesc tool?
by Tsomo on Fri, 2021-10-01 09:48
16 by David_1
Sun, 2022-06-19 17:23
VESC Tool
Normal topic CAN Commands to control VESC 100/250?
by harmander_sihra on Fri, 2021-12-17 01:49
1 by tecnico.solarboat
Mon, 2021-12-27 23:29
VESC Original Hardware
Normal topic Can control Vesc 100/250
by David_1 on Sat, 2022-06-18 01:31
1 by David_1
Sun, 2022-06-19 19:44
General discussion
Normal topic CAN defect? 4WD - CAN does not detect anymore... HELP!
by MountainBen on Tue, 2021-02-02 04:04
3 by skyline1970
Fri, 2021-02-05 19:50
Third Party Hardware
Normal topic CAN eRPM report
by alxsfrm on Mon, 2022-02-07 11:01
by alxsfrm
Mon, 2022-02-07 11:01
General discussion
Normal topic Can I change control mode on the fly through the UART port?
by spork on Wed, 2019-03-13 02:24
2 by spork
Wed, 2019-03-13 15:41
General discussion
Normal topic Can i change the controller (LQFP64) with (LQFP100) with same Firmware?
by GalihRiddle on Thu, 2019-09-05 13:44
2 by GalihRiddle
Mon, 2019-09-09 13:22
General discussion
Normal topic can I fit a VESC in my e-skate?
by 6diegodiego9 on Thu, 2021-01-21 20:42
1 by skyline1970
Tue, 2021-02-02 21:30
General discussion
Normal topic Can I re-use an old Galaxy S3 to run the VESC tool?
by Munkyheed on Fri, 2019-08-02 20:00
by Munkyheed
Fri, 2019-08-02 20:00
VESC Tool
Normal topic Can I use 12V power supply?
by ryde6 on Sun, 2021-04-25 08:19
2 by vadicus
Wed, 2021-07-14 21:01
General discussion
Normal topic Can larger BLDC motors be controlled with VESC?
by Heimfried on Sun, 2020-02-02 21:29
3 by Heimfried
Thu, 2020-02-06 22:39
General discussion
Normal topic Can motor parameters be detected with shaft load?
by powerlabor001 on Thu, 2018-03-15 13:24
4 by powerlabor001
Sat, 2018-03-24 03:07
General discussion
Normal topic Can not adjust the RPM on my 1350 w motor
by Arne Norway on Wed, 2019-01-09 18:47
6 by sam.vanratt
Sun, 2019-01-13 13:36
General discussion
Normal topic Can not run again after run perfectly !! Pls help
by Streetstar69 on Tue, 2021-11-23 03:03
1 by frank
Tue, 2021-11-23 10:03
General discussion
Normal topic can not start motor with high duty
by qdxiatao on Sat, 2018-03-24 03:58
by qdxiatao
Sat, 2018-03-24 03:58
General discussion
Normal topic Can not update firmware on FLIPSKY 4.12, still af 3.4 (att. newbie)
by SlinBin on Wed, 2019-03-27 21:59
11 by thewho
Thu, 2020-07-16 18:06
Third Party Hardware
Normal topic CAN not working on VESC MkV
by chundri on Tue, 2021-01-12 15:06
1 by chundri
Wed, 2021-01-13 15:48
VESC Original Hardware
Normal topic CAN sends error frame
by dgarciasoto on Wed, 2022-04-27 07:11
by dgarciasoto
Wed, 2022-04-27 07:11
VESC Firmware
Normal topic Can someone help me understand why I've burned up a DRV8302 in less than 10 seconds?
by shimdidly on Fri, 2017-10-13 02:01
3 by shimdidly
Mon, 2017-10-16 17:13
General discussion

Pages

Subscribe to Active forum topics