You are here
Active forum topics
Primary tabs
Topic |
Replies | Last post | Forum | |
|---|---|---|---|---|
|
Trouble downloading the tool by maxhertz on Tue, 2022-01-25 03:12 |
6 |
by frank Sat, 2022-02-05 11:02 |
VESC Tool | |
|
Trouble shooting setup by GeoffGuest on Sat, 2020-10-03 06:12 |
by GeoffGuest Sat, 2020-10-03 06:12 |
VESC Original Hardware | ||
|
Trouble with custom hardware design by Evgeni on Sun, 2022-03-06 21:46 |
4 |
by Evgeni Tue, 2022-03-15 21:20 |
Third Party Hardware | |
|
Trouble with FSESC75200 by Erik on Wed, 2020-10-07 19:09 |
by Erik Tue, 2020-10-13 15:07 |
Third Party Hardware | ||
|
Trouble with Sensorless Startup on Trampa 6376 160Kv Motors (VESC 6 Dual, FW 6.05) by bojfik on Mon, 2025-05-26 14:35 |
1 |
by bojfik Tue, 2025-05-27 15:51 |
General discussion | |
|
Troubleshooting Newborn VESC by vadicus on Tue, 2019-04-09 02:13 |
3 |
by vadicus Tue, 2019-05-14 02:06 |
Third Party Hardware | |
|
Truncated maximum motor current values by kaxorpie on Sun, 2020-12-27 23:28 |
5 |
by kaxorpie Wed, 2020-12-30 00:16 |
Feature Requests | |
|
Trying to build a can sniffer for vesc with an esp32 by Duz on Fri, 2024-07-19 19:45 |
by Duz Fri, 2024-07-19 19:45 |
Projects incorporating VESC technology | ||
|
Trying to connect over USB, but new 6.4 connects and disconnects a few seconds later. by MaxMaker1 on Thu, 2018-05-24 16:15 |
12 |
by frank Thu, 2019-02-21 20:34 |
VESC Tool | |
|
trying to get torque with speed (flipsky 75100) by Trecit0n on Fri, 2025-08-01 21:19 |
4 |
by Trecit0n Tue, 2025-08-12 00:05 |
General discussion | |
|
Trying to make motor-control work for predetermined motions, could use some help by Davideo on Fri, 2019-08-16 01:20 |
1 |
by s0313045 Mon, 2019-08-19 05:12 |
General discussion | |
|
Trying to read and set MCCONF by Jamie42 on Tue, 2020-03-24 19:47 |
by Jamie42 Tue, 2020-03-24 19:47 |
General discussion | ||
|
Trying to run a refrigerant compressor's BLDC with VESC by logansheaf on Wed, 2025-01-29 02:01 |
2 |
by logansheaf Wed, 2025-01-29 23:23 |
General discussion | |
|
Trying to upgrade old Enertion FOCBOX Fw 2.18 by jyl087 on Fri, 2024-09-13 16:26 |
by jyl087 Fri, 2024-09-13 17:31 |
Third Party Hardware | ||
|
Tuning Advanced Settings For BLDC by DjSourD on Wed, 2020-08-26 05:51 |
1 |
by trademarkaaron Tue, 2023-11-28 18:42 |
General discussion | |
|
tuning low kv high pole sensorless outrunner by cdlapoin on Tue, 2025-05-20 22:14 |
3 |
by flagoworld Wed, 2025-12-10 19:29 |
General discussion | |
|
tuning PID speed for the skateboard motor with hall sensors by salviador on Tue, 2021-09-14 14:37 |
1 |
by skyline1970 Sat, 2021-09-18 11:18 |
General discussion | |
|
Tuning process? by wingborne on Tue, 2020-09-29 00:09 |
by wingborne Tue, 2020-09-29 21:39 |
General discussion | ||
|
Tuning prop loads with rapid erpm increase in duty cycle or speed control by mirage98 on Mon, 2022-09-26 01:51 |
1 |
by drummerboy5408 Mon, 2022-10-24 05:49 |
General discussion | |
|
Tuning strategy for a large motor? by MrSurly on Tue, 2022-11-01 06:51 |
1 |
by vadicus Mon, 2022-11-14 18:23 |
General discussion |
Pages
