You are here
Active forum topics
Primary tabs
| Topic | Replies | Last post |
Forum |
|
|---|---|---|---|---|
|
Under-voltage fault with PMSM powered by bench supply by leheim on Fri, 2024-04-26 15:32 |
1 |
by electricfox Thu, 2024-05-02 10:19 |
VESC Tool | |
|
Can't update firmware on VESC 6 Firmware 3.54 by tarifachris on Fri, 2025-09-19 02:57 |
by tarifachris Fri, 2025-09-19 02:57 |
VESC Tool | ||
|
KV command in terminal ( how to determine kv of a motor ) by fessyfoo on Sat, 2020-05-09 21:21 |
1 |
by rafeh1 Mon, 2022-08-08 04:31 |
VESC Tool | |
|
How can we log all the real time data like motor current, battery current,etc to analyze them later? by vimi94 on Thu, 2019-05-02 09:57 |
27 |
by Stock88 Sun, 2024-11-03 04:02 |
VESC Tool | |
|
Vesc 6, FW 5.1, WH charged is not being logged by BalorNG on Thu, 2020-12-03 14:19 |
by BalorNG Thu, 2020-12-03 14:19 |
VESC Tool | ||
|
How to access VESC error codes in the new VESC tool by berno3 on Tue, 2018-06-05 08:47 |
1 |
by Roger Wolff Wed, 2018-06-06 07:36 |
VESC Tool | |
|
Adc throttle by Dmitry on Tue, 2020-07-28 08:55 |
by Dmitry Tue, 2020-07-28 08:55 |
VESC Tool | ||
|
Sailboat regen by flydr2 on Wed, 2023-04-12 20:10 |
1 |
by vadicus Wed, 2023-05-10 20:06 |
VESC Tool | |
|
Advanced settings for FOC motor detection (flux linkage) by jaghori.sasan on Sun, 2019-02-17 09:34 |
2 |
by jaghori.sasan Sun, 2019-02-17 17:51 |
VESC Tool | |
|
VESC tool repeatedly not recognising firmware by granstubbe on Sun, 2019-05-19 20:59 |
10 |
by Brian123 Sat, 2022-05-21 00:46 |
VESC Tool | |
|
Control VESC with PPM and Simultaneously get Data with CAN by warhawk on Wed, 2024-03-13 06:23 |
by warhawk Wed, 2024-03-13 06:42 |
VESC Tool | ||
|
VESC tool load empty by arminoonk on Thu, 2020-01-16 14:51 |
by arminoonk Thu, 2020-01-16 14:51 |
VESC Tool | ||
|
Writing to slave vesc sometimes cause loss of can bus by meashman on Wed, 2022-07-20 01:08 |
2 |
by frank Thu, 2022-10-27 08:54 |
VESC Tool | |
|
liFePo4 battery option by leonplestenjak on Mon, 2024-07-08 13:18 |
by leonplestenjak Mon, 2024-07-08 13:18 |
VESC Tool | ||
|
Vesc Tool not opening on windows computer by maccert on Sat, 2019-03-02 11:04 |
2 |
by Luca Torani Sun, 2019-03-03 20:32 |
VESC Tool | |
|
Use ADC2 as reverse button for ADC+UART/Current Reverse Button by jessejay356 on Mon, 2024-09-23 01:06 |
by jessejay356 Mon, 2024-09-23 01:06 |
VESC Tool | ||
|
Voltage measurement calibration? by pyryjansson on Tue, 2019-04-30 20:19 |
2 |
by frank Wed, 2022-11-30 09:55 |
VESC Tool | |
|
FOC detection.... by Roger Wolff on Thu, 2018-05-24 17:37 |
3 |
by TechAUmNu Sun, 2018-05-27 21:14 |
VESC Tool | |
|
Taking 5-6 seconds for running motor under ADC mode by asnamp on Fri, 2022-06-24 13:02 |
1 |
by skyline1970 Thu, 2022-11-24 21:24 |
VESC Tool | |
|
4k monitor problem by nlabs on Wed, 2017-11-01 07:36 |
3 |
by benjamin Fri, 2017-11-03 09:22 |
VESC Tool |
Pages
