You are here
Active forum topics
Primary tabs
| Topic | Replies | Last post |
Forum |
|
|---|---|---|---|---|
|
DIY VESC 6 "DRV" FAULT by a.dahhak on Thu, 2020-06-11 22:10 |
2 |
by a.dahhak Fri, 2020-06-12 20:06 |
General discussion | |
|
Motor Overheating in FOC by amanpereira1 on Thu, 2022-05-05 16:14 |
2 |
by Nuppen Wed, 2024-02-14 08:14 |
General discussion | |
|
Torque control with PWM at 10kHz for LinuxCNC + MESA + AC servo by antonchromjak on Tue, 2018-03-06 08:01 |
6 |
by Artabotak Sat, 2024-01-06 09:24 |
General discussion | |
|
Very Large hub motor detection (QSMOTOR 3000W hub) by shaman on Thu, 2020-02-20 01:26 |
5 |
by fart Wed, 2024-04-03 10:43 |
General discussion | |
|
FOC settings are working in one VESC hardware and not in another VESC hardware with same hardware version ( VESC 6MKVI ) by Pranit Bhamare on Fri, 2023-02-17 07:17 |
by Pranit Bhamare Fri, 2023-02-17 07:17 |
General discussion | ||
|
2kW motor with VESS 75200 by Sazabi on Fri, 2024-04-05 11:17 |
by Sazabi Fri, 2024-04-05 11:18 |
General discussion | ||
|
RPi 5 and VESC over UART by XAQ on Wed, 2025-09-10 07:27 |
by XAQ Wed, 2025-09-10 19:33 |
General discussion | ||
|
Cruise control by setting RPM over UART by solidgeek on Thu, 2018-02-15 10:56 |
3 |
by Lzx19961014 Thu, 2018-07-05 11:20 |
General discussion | |
|
Connect both hall and incremental quadrature encoders by vpl on Tue, 2019-01-15 14:24 |
1 |
by galp Thu, 2019-01-24 14:25 |
General discussion | |
|
Reprogram VESC for sensorless motor by Christopherinco... on Thu, 2020-09-03 00:10 |
2 |
by vadicus Thu, 2020-09-03 01:14 |
General discussion | |
|
when speed of vesc motor too fast and the arduino pin signal is unstable by HumorLogic on Tue, 2021-04-06 14:21 |
3 |
by woliam Sat, 2021-04-10 15:17 |
General discussion | |
|
Auxiliary Output Mode pin# by garyp on Sat, 2020-08-22 18:17 |
by garyp Sat, 2020-08-22 18:17 |
General discussion | ||
|
Reverse direction by ISanberg on Sun, 2021-03-28 22:22 |
1 |
by skyline1970 Sat, 2021-09-18 12:01 |
General discussion | |
|
Small inrunner HFI set-up issue by anthony_ on Thu, 2022-08-11 13:43 |
2 |
by anthony_ Mon, 2022-08-15 13:45 |
General discussion | |
|
Sensorless FOC with Duty Cycle will not stop spinning by moose09876 on Mon, 2022-08-01 18:08 |
by moose09876 Mon, 2022-08-01 18:08 |
General discussion | ||
|
limits to reprogramming VESCs by wjpremerlani on Wed, 2023-06-21 09:11 |
2 |
by wjpremerlani Thu, 2023-06-22 20:13 |
General discussion | |
|
HFI with PPM in Duty Cycle by DaganWal on Fri, 2024-08-30 00:30 |
by DaganWal Fri, 2024-08-30 00:30 |
General discussion | ||
|
bldc_interface_set_current and bldc_interface_set_rpm troubles by kristof_lr on Wed, 2019-04-24 17:20 |
by kristof_lr Wed, 2019-04-24 17:20 |
General discussion | ||
|
-solved- by KittenDude on Sat, 2020-11-28 06:30 |
by KittenDude Sun, 2020-11-29 19:27 |
General discussion | ||
|
Firmware Update = Quiet Motor? by worldmaverik on Sun, 2020-04-19 21:45 |
by worldmaverik Sun, 2020-04-19 21:45 |
General discussion |
Pages
