You are here
Active forum topics
Primary tabs
| Topic | Replies | Last post |
Forum |
|
|---|---|---|---|---|
|
Motor seize and ERPM current ramp speed by krabsheva on Tue, 2025-05-13 06:49 |
by krabsheva Tue, 2025-05-13 07:00 |
General discussion | ||
|
VESC Tool FOC detect success, but no motor running by w0nseok on Sun, 2021-11-28 11:09 |
1 |
by frank Sun, 2021-11-28 20:03 |
General discussion | |
|
VESC Not Functioning with Magnetic or Quadrature Encoders by privvyledge on Wed, 2023-05-24 16:59 |
1 |
by electricfox Thu, 2023-05-25 21:10 |
General discussion | |
|
Welding with the VESC by doomy1986 on Mon, 2020-04-13 14:38 |
by doomy1986 Mon, 2020-04-13 14:38 |
General discussion | ||
|
resistance and inductance value changes when each measurement by alexshen2012 on Fri, 2022-07-01 05:42 |
by alexshen2012 Fri, 2022-07-01 05:42 |
General discussion | ||
|
Stall torque in sensorless mode by cromoly on Sun, 2018-11-25 07:54 |
4 |
by spork Thu, 2018-11-29 03:23 |
General discussion | |
|
Motor is "pumping" under load in current control mode. is this normal? by etienne on Sat, 2023-05-13 17:16 |
2 |
by iv.kravchenko Sat, 2023-05-20 08:31 |
General discussion | |
|
Voltage Calibration by Frantin on Mon, 2026-04-20 21:40 |
by Frantin Mon, 2026-04-20 21:40 |
General discussion | ||
|
VESC Firm for Xiaomi ESC (STM32F103) uC by Foujiwara on Sat, 2020-04-04 19:16 |
3 |
by cara Mon, 2023-08-28 04:45 |
General discussion | |
|
help needed with raptor 2 remote by dave9401 on Mon, 2020-11-02 10:26 |
by dave9401 Mon, 2020-11-02 10:26 |
General discussion | ||
|
Emergency Stop SSR - Blowing up Microcontroller by J_W97 on Tue, 2022-03-01 14:46 |
5 |
by frank Tue, 2022-03-01 20:19 |
General discussion | |
|
BLDC Variable Speed Trigger for ADC throttle control by KCDEF on Mon, 2020-09-21 01:41 |
2 |
by thefallen Tue, 2020-09-22 10:53 |
General discussion | |
|
Maximum Motor RPM will not reached by Skyver on Sun, 2022-01-23 10:53 |
by Skyver Sun, 2022-01-23 10:53 |
General discussion | ||
|
vesctool 6.06 for Mac? by gregd72002 on Sat, 2025-09-27 03:36 |
3 |
by electricfox Sat, 2025-10-25 21:34 |
General discussion | |
|
Rough Motor Running When USB Cable At Vesc Tool is Disconnected by David Cunliffe on Sun, 2022-01-16 11:42 |
11 |
by David Cunliffe Sun, 2022-01-16 15:32 |
General discussion | |
|
PID control with VESC by Hacker king on Mon, 2018-03-05 20:05 |
1 |
by Danny Bokma Tue, 2018-03-06 06:19 |
General discussion | |
|
un-commanded reverse pulse by maxhurtz on Fri, 2022-09-02 16:01 |
5 |
by canoeman Thu, 2022-09-15 19:21 |
General discussion | |
|
How low is "low" inductance motors? by shaman on Sat, 2019-10-05 01:59 |
6 |
by MargaretHoffman Wed, 2023-02-22 23:07 |
General discussion | |
|
A real Noob Question by donrecardo on Sat, 2020-05-23 16:56 |
2 |
by donrecardo Fri, 2020-06-05 10:38 |
General discussion | |
|
ramping up RPM over uart (solved) by Davideo on Wed, 2018-02-14 13:13 |
2 |
by Davideo Thu, 2018-02-15 02:59 |
General discussion |
Pages
