You are here
Active forum topics
Primary tabs
| Topic | Replies | Last post |
Forum |
|
|---|---|---|---|---|
|
Using VESC remote with non-VESC ESC by Ptkend on Tue, 2022-11-15 17:21 |
6 |
by Ptkend Sun, 2022-11-20 14:04 |
General discussion | |
|
DRV8302 Gate Pin output waveform is abnormal by yandongyu1998 on Fri, 2019-12-13 07:21 |
by yandongyu1998 Fri, 2019-12-13 07:21 |
General discussion | ||
|
High voltage vesc 75/250 Field Weakening by reubarb.scons on Wed, 2022-03-02 08:45 |
2 |
by reubarb.scons Tue, 2022-03-15 07:14 |
General discussion | |
|
Current controller issue - Glitches at low current, low RPM by GijsB on Sun, 2022-10-30 12:59 |
1 |
by GijsB Sun, 2022-10-30 15:37 |
General discussion | |
|
Help with understanding/using PID control by Groundspeed100 on Tue, 2025-03-11 15:58 |
by Groundspeed100 Tue, 2025-03-11 16:01 |
General discussion | ||
|
Setting up low KV brushless motor? by Trent on Sun, 2019-12-01 02:09 |
4 |
by Trent Wed, 2019-12-04 07:54 |
General discussion | |
|
Design custom VESC 6 Hardware by brightlightbeam on Sat, 2020-07-04 14:18 |
5 |
by Gatze Mon, 2022-04-18 18:22 |
General discussion | |
|
How does Current mode work by vescflyer on Thu, 2021-10-28 15:26 |
2 |
by vescflyer Fri, 2021-10-29 08:11 |
General discussion | |
|
Speed control tuning for 500-1000 RPM by vadimz on Sun, 2018-09-02 18:09 |
2 |
by vadimz Sat, 2018-09-15 14:08 |
General discussion | |
|
Vesc Tools by Don on Sat, 2021-02-13 14:25 |
by Don Sat, 2021-02-13 14:25 |
General discussion | ||
|
wont gonnect by rustman01 on Wed, 2025-11-05 19:26 |
by rustman01 Wed, 2025-11-05 19:26 |
General discussion | ||
|
Cannot connect to VESC via USB or SWD by hagis on Wed, 2020-09-23 17:21 |
by hagis Wed, 2020-09-23 17:21 |
General discussion | ||
|
ADC1 problems with Firmware/Hardware issue? by sam.vanratt on Thu, 2018-12-27 22:31 |
4 |
by sam.vanratt Thu, 2019-01-03 17:46 |
General discussion | |
|
Problem with Android app by Er-Chispa on Wed, 2025-10-08 20:58 |
by Er-Chispa Wed, 2025-10-08 21:02 |
General discussion | ||
|
Disabling brakes when ADC is set to zero by dsuresh on Wed, 2021-04-14 23:36 |
1 |
by diler Sat, 2021-04-17 11:01 |
General discussion | |
|
Anti cogging, suppressing torque ripple? by Alistair Goodman on Wed, 2022-01-19 11:33 |
4 |
by Alistair Goodman Thu, 2022-01-20 11:11 |
General discussion | |
|
Encoder maximum PPR/CPR by Michelle90 on Mon, 2022-09-05 22:16 |
by Michelle90 Mon, 2022-09-05 22:16 |
General discussion | ||
|
At standstill a 30A limit? by Roger Wolff on Fri, 2017-11-17 09:37 |
2 |
by Roger Wolff Sat, 2017-11-18 11:58 |
General discussion | |
|
Sending RPM via UART to STM32 by EmirDns on Sat, 2022-01-08 11:00 |
3 |
by EmirDns Mon, 2022-02-07 17:38 |
General discussion | |
|
Throttle curves by Phill Dixon on Wed, 2018-05-23 18:16 |
1 |
by Tilman Baumann Thu, 2018-05-24 11:33 |
General discussion |
Pages
