You are here
Active forum topics
Primary tabs
Topic | Replies | Last post | Forum | |
---|---|---|---|---|
Sticky:
Step by Step Setup by frank on Wed, 2017-10-04 17:15 |
8 |
by mc Tue, 2018-02-20 11:12 |
VESC Tool | |
Full Brake vs Switch Off by meisterpro on Mon, 2021-03-22 14:36 |
by meisterpro Mon, 2021-03-22 14:36 |
VESC Tool | ||
Motor wizard settings by ESCam on Thu, 2018-11-08 22:49 |
8 |
by dtp Mon, 2023-11-20 00:49 |
VESC Tool | |
VESC tool load empty by arminoonk on Thu, 2020-01-16 14:51 |
by arminoonk Thu, 2020-01-16 14:51 |
VESC Tool | ||
HFI plot by Rick van der Sloot on Sun, 2022-10-02 22:26 |
by Rick van der Sloot Sun, 2022-10-02 22:26 |
VESC Tool | ||
VESCTOOL - Multiple VESC simultaneous configuration (Same CANBUS ID issues) by Filcas on Thu, 2021-02-18 20:52 |
2 |
by Filcas Fri, 2021-02-19 01:37 |
VESC Tool | |
Serial Control From PC by aguzel on Fri, 2020-08-21 02:45 |
3 |
by Jens Mon, 2022-11-28 20:40 |
VESC Tool | |
Motor whine with HFI? by christopher.h.poole on Mon, 2021-04-19 15:49 |
2 |
by christopher.h.poole Tue, 2021-06-15 21:18 |
VESC Tool | |
Detection failed. Reason: Sensor detection failed by Lilian_CASTEL on Tue, 2020-11-24 11:31 |
8 |
by electricfox Thu, 2023-02-16 15:57 |
VESC Tool | |
Motor RPM counter in Dashboard and Mob App by Rex on Fri, 2022-06-17 07:01 |
by Rex Fri, 2022-06-17 07:01 |
VESC Tool | ||
How to Enable kill switch support in Firmware 5.03 by iserai2r on Sat, 2022-02-05 13:59 |
5 |
by rodrigo.baronio Tue, 2023-02-14 02:27 |
VESC Tool | |
Maxkgo bms configuration inside vesc tool by renaudbarbier on Fri, 2024-04-19 15:53 |
by renaudbarbier Fri, 2024-04-19 15:53 |
VESC Tool | ||
Max RPM by donrecardo on Thu, 2020-06-25 12:00 |
1 |
by Tibor Kalman Za... Mon, 2020-06-29 21:03 |
VESC Tool | |
"bad detection result received" impossible to achieved motor detection ! by titimomotete on Wed, 2019-03-20 17:21 |
2 |
by doom Mon, 2019-08-05 10:52 |
VESC Tool | |
PPM Pulselength mapping by Shaftdriver on Tue, 2022-10-04 19:50 |
1 |
by skyline1970 Thu, 2022-11-24 20:15 |
VESC Tool | |
PPM read has an offset by tuloski on Thu, 2018-09-13 09:38 |
2 |
by Stupidspencer Fri, 2019-07-19 03:09 |
VESC Tool | |
VESC Tool Platinum : Windows 7 - Not working by moorem on Mon, 2020-05-18 23:19 |
2 |
by TheFallen Tue, 2020-12-15 12:06 |
VESC Tool | |
ADC Input Change by alivedom on Thu, 2017-12-14 15:18 |
6 |
by andrecorreia Thu, 2021-04-29 14:44 |
VESC Tool | |
FOC Encoder autotune issue by David_Lo on Tue, 2020-01-21 11:54 |
by David_Lo Tue, 2020-01-21 11:54 |
VESC Tool | ||
PPM Configuration is Only Working While Connected to VESC Software by kyle45 on Wed, 2020-01-15 05:13 |
2 |
by frank Mon, 2020-01-27 21:03 |
VESC Tool |