You are here
Active forum topics
Primary tabs
| Topic | Replies | Last post |
Forum |
|
|---|---|---|---|---|
|
Set and measure RPM - Questions by Piep on Thu, 2018-11-08 16:10 |
by Piep Thu, 2018-11-08 16:10 |
General discussion | ||
|
VESC first build questions by evbkez on Fri, 2019-08-02 14:58 |
1 |
by TittyTwister Sun, 2022-07-10 21:35 |
General discussion | |
|
FRF measurement functionality by Elwin on Sun, 2021-10-31 01:06 |
11 |
by Elwin Sat, 2021-11-06 22:05 |
General discussion | |
|
How does controlling two different motors over CAN bus really work? by oangelo on Sat, 2023-04-15 20:05 |
by oangelo Sat, 2023-04-15 20:05 |
General discussion | ||
|
Flipsky 72150 outboard cannot connect via USB by EddieEagle1970 on Sat, 2026-02-21 16:56 |
2 |
by mariuszdymon Sat, 2026-02-28 23:37 |
General discussion | |
|
FSESC6.6+ Over Voltage Fault 80mm Motors by Yomiel on Fri, 2020-03-20 03:45 |
4 |
by thefallen Mon, 2021-03-01 16:47 |
General discussion | |
|
VESC with auto calibration of grace one motor (videos included) by ligi on Mon, 2020-10-19 02:13 |
10 |
by ligi Tue, 2020-11-17 06:56 |
General discussion | |
|
Motor temperature increase by e-biker on Sun, 2018-04-08 20:17 |
4 |
by e-biker Mon, 2018-04-09 14:44 |
General discussion | |
|
Updated firmware and remote doesn't work by Africaans on Sat, 2022-01-29 22:18 |
3 |
by jasson Tue, 2022-02-08 09:19 |
General discussion | |
|
VESC packet fram-size by Yosh101 on Fri, 2022-09-30 15:34 |
by Yosh101 Fri, 2022-09-30 15:34 |
General discussion | ||
|
Throttle mapping issue by forcefed on Fri, 2018-03-30 15:37 |
2 |
by Burak Thu, 2023-12-07 13:21 |
General discussion | |
|
VESC on DIY CNC router by tbartoletta on Wed, 2019-02-20 03:00 |
5 |
by GunnarW Thu, 2019-02-21 16:44 |
General discussion | |
|
how connect bluetooth module nRF52832 ? by netev on Mon, 2022-09-19 18:11 |
4 |
by TPEHAK Mon, 2025-08-04 06:26 |
General discussion | |
|
Rickshaw Motor - Typical 48V 1000W motors available by sweendog311 on Wed, 2023-09-20 22:52 |
by sweendog311 Wed, 2023-09-20 22:52 |
General discussion | ||
|
Spintend v2 100amp 100volt by Phill Dixon on Wed, 2024-12-04 18:14 |
1 |
by electricfox Wed, 2024-12-04 20:06 |
General discussion | |
|
VESC Questions from the newbie by mendez on Fri, 2019-02-08 21:13 |
10 |
by frank Mon, 2019-02-18 08:52 |
General discussion | |
|
Using Hall as encoder input by Offline on Tue, 2021-01-19 10:41 |
by Offline Mon, 2021-02-08 10:19 |
General discussion | ||
|
NEW HARDWARE RELEASED!!! | DF_ESC Electric Motor Controller | YouTube Series Walkthrough by d.fresu on Mon, 2023-08-14 18:29 |
by d.fresu Mon, 2023-08-14 18:29 |
General discussion | ||
|
Controller just shuts off by Stock88 on Sun, 2024-11-03 03:49 |
1 |
by electricfox Sun, 2024-11-03 09:08 |
General discussion | |
|
Problem with breaking in use in RC plane by fluffy on Tue, 2020-05-26 06:11 |
3 |
by fluffy Sat, 2020-05-30 03:54 |
General discussion |
Pages
