You are here
Active forum topics
Primary tabs
| Topic | Replies | Last post |
Forum |
|
|---|---|---|---|---|
|
can not start motor with high duty by qdxiatao on Sat, 2018-03-24 03:58 |
by qdxiatao Sat, 2018-03-24 03:58 |
General discussion | ||
|
VESC - Motor will not start until a small kick is applied from a full stop despite using hall sensors by 010203040506070809 on Wed, 2019-10-23 23:12 |
by 010203040506070809 Wed, 2019-10-23 23:12 |
General discussion | ||
|
vesc tool not giving me the right values by spacemango on Tue, 2020-06-09 13:31 |
by spacemango Tue, 2020-06-09 13:42 |
General discussion | ||
|
controlling 2 motors for two directions each by ori harush on Mon, 2022-06-06 07:17 |
4 |
by Indy8976 Tue, 2022-06-21 13:36 |
General discussion | |
|
Motor runs only at constant speed (with VESC 100V200A and Flipsky VX3). by Tom65 on Wed, 2023-04-12 16:28 |
by Tom65 Wed, 2023-04-12 16:28 |
General discussion | ||
|
Custom code changes- I/O pin go high or low by dsuresh on Thu, 2021-05-13 19:50 |
2 |
by dsuresh Fri, 2021-05-14 22:30 |
General discussion | |
|
How to reboot VESC from serial port by Ivko on Mon, 2021-01-04 18:44 |
by Ivko Mon, 2021-01-04 18:44 |
General discussion | ||
|
FOCBOX X is not detected by sumedh on Tue, 2022-09-13 22:16 |
3 |
by frank Mon, 2022-09-19 09:18 |
General discussion | |
|
current control mode with duty cycle limit based on throttle by devin on Thu, 2020-01-16 05:45 |
by devin Thu, 2020-01-16 05:49 |
General discussion | ||
|
Upload bootloader to stm32 f405? by jneumann on Sat, 2020-08-08 07:11 |
3 |
by TechAUmNu Sat, 2020-08-08 18:29 |
General discussion | |
|
motor output voltage vs input voltage by rsarver on Wed, 2021-03-17 15:55 |
by rsarver Wed, 2021-03-17 15:55 |
General discussion | ||
|
FAULT_CODE_DRV by protontim on Fri, 2017-10-06 04:19 |
2 |
by protontim Tue, 2017-10-10 22:34 |
General discussion | |
|
IMU 9250 and 6050 not working on new vesc 4.12 and 4.20 by trung_qly on Sun, 2021-09-05 16:11 |
3 |
by spatsirk Mon, 2025-06-09 18:55 |
General discussion | |
|
Isolated CANbus / CAN by shener on Wed, 2024-10-23 15:15 |
1 |
by Markula Thu, 2024-10-24 22:19 |
General discussion | |
|
Problems with motor and encoder in PID application by Shaik Siraaj on Thu, 2018-12-13 09:57 |
1 |
by Shaik Siraaj Fri, 2018-12-14 10:14 |
General discussion | |
|
Question on throttle response by petermarcotte1 on Wed, 2020-07-29 11:28 |
3 |
by petermarcotte1 Sat, 2020-08-01 14:17 |
General discussion | |
|
Flipsky 7550 and Ninebot Max G30 48V by shatty on Thu, 2021-03-11 07:02 |
1 |
by shatty Sat, 2021-03-13 04:55 |
General discussion | |
|
Loud Bang at Sensor-less Switchover with hub motor by hackeybabel on Sat, 2021-08-21 11:13 |
2 |
by hackeybabel Thu, 2021-08-26 07:19 |
General discussion | |
|
Where can I ask technical questions about products? by MrSurly on Tue, 2022-04-19 05:22 |
by MrSurly Tue, 2022-04-19 05:22 |
General discussion | ||
|
Reverse button not working by oangelo on Sat, 2023-02-04 21:47 |
1 |
by oangelo Tue, 2023-02-07 18:16 |
General discussion |
Pages
