You are here
Active forum topics
Primary tabs
| Topic | Replies | Last post |
Forum |
|
|---|---|---|---|---|
|
Reverse Button Status over UART? by Rich235 on Sat, 2024-09-07 10:34 |
by Rich235 Sat, 2024-09-07 10:34 |
General discussion | ||
|
Removing low speed openloop FOC parking brake mode from FW by rodread on Thu, 2018-03-08 15:01 |
4 |
by arvidb Wed, 2018-06-06 19:02 |
General discussion | |
|
how to update 4.0 firmware when only 5.0 and 5.1 firmware available by GSWconstruction on Mon, 2020-09-07 19:30 |
1 |
by frank Tue, 2020-09-22 09:18 |
General discussion | |
|
VESC with Ey4 and special function by MachWas on Mon, 2024-08-12 02:34 |
by MachWas Mon, 2024-08-12 02:34 |
General discussion | ||
|
only Encoder with no index by Dina on Mon, 2026-06-29 10:24 |
2 |
by Dina Mon, 2026-06-29 14:20 |
General discussion | |
|
Is it normal to have5th harmonic current ? by Alex Marques on Fri, 2023-02-10 16:01 |
by Alex Marques Fri, 2023-02-10 16:02 |
General discussion | ||
|
VESC 6 for AUV applications by bc on Thu, 2018-02-22 15:57 |
5 |
by arvidb Fri, 2018-02-23 19:20 |
General discussion | |
|
IPM/Salient Motor Tuning by SRFirefox on Wed, 2020-08-26 23:19 |
2 |
by JP Wed, 2022-08-17 11:22 |
General discussion | |
|
Connect 4 vesc with can-bus, motors stuttering by oyvinla on Tue, 2022-01-04 17:12 |
8 |
by ahanktcd Wed, 2024-04-17 06:35 |
General discussion | |
|
VESC Setup - Fluctuating/Unstable Duty Cycle/eRPM/Current by liminalsunset on Thu, 2022-08-04 01:44 |
by liminalsunset Thu, 2022-08-04 01:44 |
General discussion | ||
|
Motors spin during detection but then won't spin by jsbenson on Tue, 2023-06-27 23:54 |
by jsbenson Tue, 2023-06-27 23:54 |
General discussion | ||
|
Wrong software shows up. Answered my own question. by leecon on Fri, 2025-03-07 17:50 |
1 |
by leecon Tue, 2025-03-11 17:00 |
General discussion | |
|
No load FOC stops when full FWD throttle. by toboli on Mon, 2023-06-05 18:41 |
by toboli Mon, 2023-06-05 18:41 |
General discussion | ||
|
How I control the RPM of my motor from VESC with Arduino? by George W. on Sat, 2020-04-25 16:10 |
1 |
by frank Thu, 2020-04-30 18:16 |
General discussion | |
|
Noised signal from motor NTC sensor | HW4.12 FW3.27 by ma-j-sterelektron on Wed, 2017-09-06 18:41 |
10 |
by vescsci Wed, 2020-07-15 22:47 |
General discussion | |
|
*newbie* motors keep running backwards randomly when switch off, and then back on. Embarrassing. by Nikolas Lamshed on Sun, 2021-06-20 13:36 |
by Nikolas Lamshed Sun, 2021-06-20 13:36 |
General discussion | ||
|
2nd Maytech 75_300 burned by Flyingtux on Wed, 2022-03-16 22:15 |
1 |
by skyline1970 Fri, 2022-03-25 19:00 |
General discussion | |
|
Canbus slave control in duty cycle mode not working correctly by Enak on Sat, 2019-04-13 03:55 |
1 |
by benjamin Mon, 2019-04-15 10:09 |
General discussion | |
|
How can I add watts data to solidgeek? by Fixitmoditbreakit on Sat, 2021-06-12 00:07 |
2 |
by vadicus Tue, 2021-06-15 17:50 |
General discussion | |
|
Connecting handlebar controlls by mannberg on Thu, 2022-03-10 14:57 |
by mannberg Thu, 2022-03-10 14:57 |
General discussion |
Pages
