You are here
Active forum topics
Primary tabs
| Topic | Replies | Last post |
Forum |
|
|---|---|---|---|---|
|
VESC 100/250 missing hall sensor plug by steve1428 on Sat, 2023-04-08 10:00 |
1 |
by iv.kravchenko Fri, 2023-05-19 22:26 |
General discussion | |
|
ERPM settings restrict carving speed on outer wheel. Poor user experience. by Paul15578 on Fri, 2018-01-12 02:28 |
9 |
by Ackmaniac Tue, 2018-04-24 13:47 |
General discussion | |
|
Hall sensors + incremental encoder by SAK-SIVAL on Thu, 2020-10-08 18:37 |
2 |
by tonyXHB Tue, 2020-12-22 13:33 |
General discussion | |
|
Bafang BBSHD hub motor setup by csev-tcejorp on Sat, 2022-08-13 14:50 |
by csev-tcejorp Sat, 2022-08-13 14:50 |
Feature Requests | ||
|
Total ODOMETER counter via real time logging feature request by janzobanzo7 on Mon, 2022-10-24 14:49 |
6 |
by Lennart Duijn Fri, 2023-08-11 18:38 |
Feature Requests | |
|
Force Sensor for a e-skateboard by beadon on Sat, 2022-06-04 05:08 |
1 |
by frank Sat, 2022-06-04 11:24 |
Feature Requests | |
|
id/iq Table input by red.blaylock on Fri, 2020-05-22 09:20 |
1 |
by dmerkling1@gmail.com Wed, 2025-01-01 02:43 |
Feature Requests | |
|
Apply current to brake at low speed by argon338 on Wed, 2022-08-17 08:36 |
by argon338 Thu, 2022-08-25 17:08 |
Feature Requests | ||
|
Allow braking to override negative ramping time by Paul15578 on Wed, 2018-01-24 06:20 |
5 |
by benjamin Sat, 2019-02-23 10:14 |
Feature Requests | |
|
Add support for dual H3LIS331DL accelerometer by SirPolPol on Fri, 2022-04-08 09:09 |
3 |
by frank Mon, 2022-04-11 09:08 |
Feature Requests | |
|
uROS support by neuromancer2701 on Wed, 2019-11-06 21:17 |
by neuromancer2701 Wed, 2019-11-06 21:17 |
Feature Requests | ||
|
Reverse safety function by rich on Tue, 2017-09-05 10:14 |
3 |
by rich Wed, 2017-09-06 11:07 |
Feature Requests | |
|
Foc openloop soft start by Alan oldguy on Fri, 2018-09-07 03:05 |
by Alan oldguy Fri, 2018-09-07 03:05 |
Feature Requests | ||
|
Servo Motor position control by wdaehn on Wed, 2017-11-29 21:45 |
by wdaehn Wed, 2017-11-29 21:45 |
Feature Requests | ||
|
Some ideas to improve VESC by e-biker on Sun, 2018-03-18 16:36 |
3 |
by Roger Wolff Mon, 2018-04-23 08:57 |
Feature Requests | |
|
Motion commands for controlling CNCs by andresv on Fri, 2017-09-08 10:35 |
2 |
by brushlessjoe Sun, 2019-03-17 21:29 |
Feature Requests | |
|
Truncated maximum motor current values by kaxorpie on Sun, 2020-12-27 23:28 |
5 |
by kaxorpie Wed, 2020-12-30 00:16 |
Feature Requests | |
|
Expose all functions through RPC by Luke264 on Wed, 2020-12-09 19:40 |
by Luke264 Wed, 2020-12-09 19:40 |
Feature Requests | ||
|
Access to balance fault settings when using other apps for control. by crutch on Tue, 2022-03-22 11:14 |
1 |
by auspiciouszesty Mon, 2022-06-06 10:32 |
Feature Requests | |
|
Distance based on Phone GPS by Mikko Valtonen on Sat, 2020-04-25 08:33 |
by Mikko Valtonen Sat, 2020-04-25 08:38 |
Feature Requests |
Pages
