You are here
Active forum topics
Primary tabs
Topic | Replies | Last post | Forum | |
---|---|---|---|---|
vesc6 help with hub motor by badger1666 on Thu, 2018-12-20 18:36 |
4 |
by badger1666 Fri, 2018-12-21 06:03 |
General discussion | |
VESC/FOC developer needed by CAYAGO_MS on Thu, 2020-04-30 14:23 |
by CAYAGO_MS Thu, 2020-04-30 14:23 |
General discussion | ||
New at VESC Tool by TheButaner on Sun, 2023-06-04 21:38 |
1 |
by Gos1 Mon, 2023-06-26 11:37 |
General discussion | |
How to control two Can-connected motors separately from microcontroller. by kkkeisuke on Sun, 2021-06-20 06:47 |
by kkkeisuke Sun, 2021-06-20 12:05 |
General discussion | ||
Request: Report hall sensor tables. by Roger Wolff on Thu, 2018-05-17 15:28 |
7 |
by Tilman Baumann Mon, 2018-08-06 12:24 |
General discussion | |
VESC fault over voltage by ilhamdestyo on Wed, 2023-08-02 16:47 |
1 |
by electricfox Thu, 2023-08-03 08:19 |
General discussion | |
Dual Motor Software "Limited Slip" Differential by luky on Thu, 2021-06-10 10:43 |
1 |
by frank Thu, 2021-06-10 11:07 |
General discussion | |
Can bus and BLDC vs FOC by Torbjorn on Fri, 2022-11-11 11:08 |
4 |
by Torbjorn Tue, 2022-11-15 14:37 |
General discussion | |
Current control and duty cycle issues. by ESCam on Tue, 2019-04-02 22:55 |
by ESCam Tue, 2019-04-02 22:55 |
General discussion | ||
Pitting VESC Six EDU against a Castle Creations ESC - the Castle is winning? by jschall on Fri, 2023-07-14 18:58 |
4 |
by drummerboy5408 Thu, 2023-11-02 23:24 |
General discussion | |
Current mismatch between power supply and vesc tool by mansi712 on Tue, 2024-09-24 13:02 |
by mansi712 Tue, 2024-09-24 18:08 |
General discussion | ||
Encoder position resetting to 0° by Michelle90 on Tue, 2022-10-25 18:55 |
1 |
by GijsB Sun, 2022-10-30 20:17 |
General discussion | |
Can bus communication. by Piamen on Wed, 2019-11-27 06:47 |
by Piamen Wed, 2019-11-27 06:47 |
General discussion | ||
Using VESC to drive sensorless linear motor to simulate on/off solenoid by cmcraeslo on Wed, 2020-07-01 09:15 |
1 |
by pf26 Mon, 2020-07-06 11:10 |
General discussion | |
how to delete pc install, struggling to get the mobile program to work :) by jon218white on Thu, 2021-02-18 20:47 |
1 |
by TheFallen Fri, 2021-02-19 00:31 |
General discussion | |
DRV8302 sensibility by lurch on Sat, 2021-10-23 23:37 |
19 |
by lurch Sat, 2021-10-30 10:13 |
General discussion | |
VESC 6 motor setup: Resistance measurement jumps by thomasjfox on Mon, 2017-10-09 20:42 |
2 |
by thomasjfox Sat, 2017-10-28 21:57 |
General discussion | |
Poor Slow Speed Control by dcw_jubilee on Wed, 2024-02-14 13:35 |
1 |
by GiBi77930 Fri, 2024-06-14 10:34 |
General discussion | |
Communication with Vesc Tools by faheemift on Tue, 2021-02-09 16:08 |
8 |
by beatrixena Sat, 2021-02-20 09:11 |
General discussion | |
Starting rotation by changing duty cicle- current increases shortly (ms) and dcreases immediately to 0A by simon_snow on Wed, 2021-10-06 22:15 |
4 |
by simon_snow Fri, 2021-10-08 12:49 |
General discussion |