You are here
Active forum topics
Primary tabs
| Topic | Replies | Last post |
Forum |
|
|---|---|---|---|---|
|
software download problem by netev on Sun, 2022-09-18 22:28 |
2 |
by netev Mon, 2022-09-19 12:28 |
General discussion | |
|
Tach output changes when switching from BLDC --> FOC by Zoxks on Sun, 2024-12-01 20:28 |
1 |
by Zoxks Tue, 2024-12-03 19:10 |
General discussion | |
|
Connecting the VESC6 plus with servo wires by GreenPenguin on Wed, 2019-10-16 15:39 |
1 |
by frank Thu, 2019-10-17 11:11 |
General discussion | |
|
VESC 75/300 and EMC Tests for motorcycle conversion by gotfatalErrs on Tue, 2020-06-02 18:34 |
8 |
by Bubu54 Wed, 2024-09-04 13:52 |
General discussion | |
|
Negative current reporting at high erpm in no-load setup by mcdanny on Sun, 2021-01-17 23:04 |
1 |
by moto_guy Sat, 2021-01-30 04:53 |
General discussion | |
|
Power Switch by flyingbrike on Wed, 2021-09-08 13:47 |
by flyingbrike Wed, 2021-09-08 13:47 |
General discussion | ||
|
Questions regarding adc1/2 whilst using one thumb joystick. by Ben26 on Wed, 2024-10-30 12:48 |
3 |
by Ben26 Sat, 2024-11-02 22:19 |
General discussion | |
|
FlipSky 75/300 + Alien 80 KV noise/vibration under load by brendangillatt on Thu, 2021-01-07 01:19 |
13 |
by Thejesh Bollineni Wed, 2025-04-30 22:49 |
General discussion | |
|
Vesc is not turning on by asnamp on Wed, 2022-04-20 09:30 |
1 |
by canoeman Wed, 2022-04-20 15:44 |
General discussion | |
|
ws8212 and VESC firmware by dannlh on Fri, 2017-11-03 04:17 |
2 |
by dannlh Sat, 2017-11-04 18:47 |
General discussion | |
|
Newbie - controller/motor not working by JLow75 on Tue, 2018-11-13 09:50 |
3 |
by bsissell Fri, 2021-11-26 07:17 |
General discussion | |
|
"Throttle" help by benha on Wed, 2019-08-07 05:58 |
by benha Wed, 2019-08-07 05:58 |
General discussion | ||
|
Torque control setting by mambazhasa@uni.... on Thu, 2023-01-26 17:24 |
3 |
by Davidepolpi91 Tue, 2024-03-19 12:45 |
General discussion | |
|
Runtime motor control with CAN by Davidepolpi91 on Fri, 2024-03-15 15:12 |
by Davidepolpi91 Fri, 2024-03-15 15:12 |
General discussion | ||
|
FOC Calibration over CAN by thisisjaye on Fri, 2018-10-26 13:15 |
1 |
by frank Fri, 2018-10-26 17:12 |
General discussion | |
|
AMT 102 Encoder not working properly with VESC by DerpRush on Thu, 2019-07-25 11:32 |
5 |
by ripperpc Wed, 2022-04-06 21:36 |
General discussion | |
|
Access the Vesc terminal using another App (Putty?) by mikej_w on Fri, 2020-01-17 02:23 |
3 |
by vadicus Tue, 2020-01-21 02:19 |
General discussion | |
|
Trouble with Sensorless Startup on Trampa 6376 160Kv Motors (VESC 6 Dual, FW 6.05) by bojfik on Mon, 2025-05-26 14:35 |
1 |
by bojfik Tue, 2025-05-27 15:51 |
General discussion | |
|
Dual VESC via CAN by scholtylicious on Sat, 2021-03-13 15:56 |
by scholtylicious Sat, 2021-03-13 15:56 |
General discussion | ||
|
Fault code sensor 1 by krille on Sat, 2022-07-23 16:31 |
1 |
by skyline1970 Thu, 2022-11-24 21:08 |
General discussion |
Pages
