You are here
Active forum topics
Primary tabs
| Topic | Replies | Last post |
Forum |
|
|---|---|---|---|---|
|
Powertool switch on VESC by Toto on Mon, 2021-09-13 12:06 |
1 |
by skyline1970 Sat, 2021-09-18 11:25 |
General discussion | |
|
how to update 4.0 firmware when only 5.0 and 5.1 firmware available by GSWconstruction on Mon, 2020-09-07 19:30 |
1 |
by frank Tue, 2020-09-22 09:18 |
General discussion | |
|
Is it normal to have5th harmonic current ? by Alex Marques on Fri, 2023-02-10 16:01 |
by Alex Marques Fri, 2023-02-10 16:02 |
General discussion | ||
|
IPM/Salient Motor Tuning by SRFirefox on Wed, 2020-08-26 23:19 |
2 |
by JP Wed, 2022-08-17 11:22 |
General discussion | |
|
Connect 4 vesc with can-bus, motors stuttering by oyvinla on Tue, 2022-01-04 17:12 |
8 |
by ahanktcd Wed, 2024-04-17 06:35 |
General discussion | |
|
VESC Setup - Fluctuating/Unstable Duty Cycle/eRPM/Current by liminalsunset on Thu, 2022-08-04 01:44 |
by liminalsunset Thu, 2022-08-04 01:44 |
General discussion | ||
|
Documentation by Cledus on Sat, 2017-12-30 22:23 |
1 |
by Oyta Tue, 2018-01-23 20:35 |
General discussion | |
|
PPM Mislabeled by stevemk14ebr on Fri, 2018-12-21 01:49 |
1 |
by Roger Wolff Tue, 2019-01-01 12:12 |
General discussion | |
|
How I control the RPM of my motor from VESC with Arduino? by George W. on Sat, 2020-04-25 16:10 |
1 |
by frank Thu, 2020-04-30 18:16 |
General discussion | |
|
*newbie* motors keep running backwards randomly when switch off, and then back on. Embarrassing. by Nikolas Lamshed on Sun, 2021-06-20 13:36 |
by Nikolas Lamshed Sun, 2021-06-20 13:36 |
General discussion | ||
|
2nd Maytech 75_300 burned by Flyingtux on Wed, 2022-03-16 22:15 |
1 |
by skyline1970 Fri, 2022-03-25 19:00 |
General discussion | |
|
How different of VESC 6 and VESC 4 by Ken_chen on Thu, 2018-05-17 18:13 |
3 |
by ripperpc Mon, 2020-05-04 07:58 |
General discussion | |
|
Canbus slave control in duty cycle mode not working correctly by Enak on Sat, 2019-04-13 03:55 |
1 |
by benjamin Mon, 2019-04-15 10:09 |
General discussion | |
|
How can I add watts data to solidgeek? by Fixitmoditbreakit on Sat, 2021-06-12 00:07 |
2 |
by vadicus Tue, 2021-06-15 17:50 |
General discussion | |
|
Connecting handlebar controlls by mannberg on Thu, 2022-03-10 14:57 |
by mannberg Thu, 2022-03-10 14:57 |
General discussion | ||
|
HFI Tuning - "Start Voltage" Question by drummerboy5408 on Sat, 2022-11-12 03:12 |
by drummerboy5408 Sat, 2022-11-12 03:12 |
General discussion | ||
|
encoder detection error by qdxiatao on Wed, 2018-05-09 12:04 |
1 |
by mona Thu, 2024-10-10 15:55 |
General discussion | |
|
SK3 Turnigy 6374 149 / encoder CUI AMT102 => can VESC 4 support position control? by fourchette on Tue, 2019-04-02 23:14 |
5 |
by pf26 Thu, 2019-04-04 11:43 |
General discussion | |
|
Calculator by kstuck on Tue, 2019-12-10 18:30 |
by kstuck Tue, 2019-12-10 18:30 |
General discussion | ||
|
Advice please - VESC6 controller for a specific model aircraft application by aabill on Wed, 2019-11-27 11:31 |
5 |
by frank Sun, 2019-12-01 17:28 |
General discussion |
Pages
