You are here
Active forum topics
Primary tabs
| Topic | Replies | Last post |
Forum |
|
|---|---|---|---|---|
|
Version 3.01 destroyed version 2.06 too by Knaubel on Sun, 2022-05-15 21:23 |
6 |
by Knaubel Wed, 2022-05-18 16:16 |
VESC Tool | |
|
Bluetooth RX/TX by eastcoastkiter on Fri, 2019-06-28 19:02 |
5 |
by radler Sat, 2020-06-20 17:06 |
VESC Tool | |
|
LSM6DS3 gyro ? for balancing by amaussa on Sun, 2020-09-13 12:51 |
1 |
by amaussa Mon, 2020-09-21 17:21 |
VESC Tool | |
|
"Allow Breaking" set to "TRUE" when "Backup COnfigurations (Including CAN) by bayetan on Mon, 2023-05-22 05:33 |
by bayetan Mon, 2023-05-22 05:33 |
VESC Tool | ||
|
FOC detection.... by Roger Wolff on Thu, 2018-05-24 17:37 |
3 |
by TechAUmNu Sun, 2018-05-27 21:14 |
VESC Tool | |
|
Motor Poles by Enak on Fri, 2017-09-08 00:57 |
1 |
by ThierryGTLTS Fri, 2017-09-08 09:01 |
VESC Tool | |
|
Can the PPM mapping be changed so that higher duty cycle means slower speed? by UncleJoe on Mon, 2020-05-25 11:46 |
3 |
by UncleJoe Thu, 2020-11-19 15:06 |
VESC Tool | |
|
RPM Limit not working by chinzw on Wed, 2017-09-06 09:29 |
5 |
by ThierryGTLTS Thu, 2017-09-07 11:05 |
VESC Tool | |
|
vesc tool not opening by RemyMade413 on Sat, 2026-02-28 12:15 |
2 |
by mariuszdymon Sat, 2026-02-28 23:07 |
VESC Tool | |
|
Bluetooth connection possible with METR device? by Cuprani on Sun, 2018-04-01 23:00 |
1 |
by Pimousse Wed, 2018-04-04 11:34 |
VESC Tool | |
|
Motor and input calibration without drive train by technique on Tue, 2020-07-14 19:22 |
by technique Tue, 2020-07-14 19:22 |
VESC Tool | ||
|
MAX ERPM by riderman on Sun, 2021-02-28 23:05 |
by riderman Sun, 2021-02-28 23:05 |
VESC Tool | ||
|
Motor FOC Config Wizard only sees "local" motor, not CAN connected by glasswalker on Mon, 2024-04-08 04:46 |
1 |
by glasswalker Mon, 2024-04-08 23:33 |
VESC Tool | |
|
Motor wizard settings by ESCam on Thu, 2018-11-08 22:49 |
8 |
by dtp Mon, 2023-11-20 00:49 |
VESC Tool | |
|
Can I re-use an old Galaxy S3 to run the VESC tool? by Munkyheed on Fri, 2019-08-02 20:00 |
by Munkyheed Fri, 2019-08-02 20:00 |
VESC Tool | ||
|
Changing Output Voltage frequency by davbams on Wed, 2019-07-24 21:20 |
1 |
by district9prawn Thu, 2019-07-25 02:59 |
VESC Tool | |
|
PPM throttle detected in Vesc Tool but has no effect on motor by maxim1977 on Sat, 2025-07-26 06:03 |
1 |
by ftpkmarcelo Sun, 2025-08-10 06:07 |
VESC Tool | |
|
VESC Tool wont start by w31x on Wed, 2020-03-11 19:30 |
9 |
by SUB13 Sun, 2024-02-11 14:43 |
VESC Tool | |
|
Old versions of VESC Tool by thefallen on Thu, 2018-07-05 19:47 |
31 |
by rafeh1 Thu, 2024-10-10 23:44 |
VESC Tool | |
|
Detection for a drone outrunner 515 kV and 775 kV by MaksK on Thu, 2020-06-04 16:05 |
by MaksK Thu, 2020-06-04 16:05 |
VESC Tool |
Pages
