You are here
Active forum topics
Primary tabs
| Topic | Replies | Last post |
Forum |
|
|---|---|---|---|---|
|
Switch between different modes via remote by Cledus on Sun, 2017-10-22 13:56 |
2 |
by MatwoSvK Tue, 2017-11-07 22:32 |
VESC Tool | |
|
foc detection params by stefann on Mon, 2020-04-13 00:07 |
by stefann Mon, 2020-04-13 00:28 |
VESC Tool | ||
|
THERE IS NO ONE IN HERE HAHA by zip on Sun, 2024-06-30 12:41 |
by zip Sun, 2024-06-30 12:41 |
VESC Tool | ||
|
Bimodal Ld-Lq Saliency on T Motor AT4130 by ohceejay on Wed, 2026-04-15 18:30 |
by ohceejay Wed, 2026-04-15 18:30 |
VESC Tool | ||
|
Motor clicking and not spinning after setup wizard by dfelz on Fri, 2020-04-03 03:51 |
6 |
by brian adilman Wed, 2022-01-26 13:36 |
VESC Tool | |
|
Delay on reverse function on electric boat by FreddyForLaunch on Tue, 2021-06-01 12:31 |
4 |
by electricfox Wed, 2022-08-17 20:59 |
VESC Tool | |
|
Is it possible to stop a motor at one exact desired location without hall sensor? by vimi94 on Thu, 2019-08-15 10:58 |
2 |
by vimi94 Tue, 2019-08-20 13:37 |
VESC Tool | |
|
PPM Pulselength mapping by Shaftdriver on Tue, 2022-10-04 19:50 |
1 |
by skyline1970 Thu, 2022-11-24 20:15 |
VESC Tool | |
|
Constant Serial port errors by SteveBrantley on Tue, 2025-01-21 23:13 |
by SteveBrantley Tue, 2025-01-21 23:13 |
VESC Tool | ||
|
VESC Tool 3.0 can't run input wizzard by thib on Mon, 2021-09-27 00:58 |
4 |
by frank Fri, 2021-10-29 10:07 |
VESC Tool | |
|
Unrecognized USB port vesc tool 1.25 by geotoine on Fri, 2019-11-08 15:35 |
1 |
by bb67 Fri, 2020-06-12 18:10 |
VESC Tool | |
|
VESC100/250 - motor current setting ignored? by tobiokanobi on Mon, 2022-05-02 13:27 |
3 |
by frank Tue, 2022-05-03 20:54 |
VESC Tool | |
|
vesc tool 1.25 not opening. by osis on Tue, 2019-10-29 20:50 |
9 |
by flyingbrike Wed, 2021-09-08 09:06 |
VESC Tool | |
|
Bug Report CONNECTION ISSUES 6.06 by andredi on Mon, 2025-09-01 17:36 |
by andredi Mon, 2025-09-01 17:36 |
VESC Tool | ||
|
cant connect via usb by curtm on Wed, 2019-06-19 03:05 |
2 |
by curtm Thu, 2019-07-04 00:37 |
VESC Tool | |
|
VESC Tool Crashing on connection (on Macbook version) by svelte.ca on Thu, 2025-07-31 00:00 |
2 |
by etavav Thu, 2025-09-18 17:19 |
VESC Tool | |
|
FOC configuration when resistance is measured as R=0. by Roger Wolff on Tue, 2018-08-28 18:20 |
2 |
by Foxyirish1987 Tue, 2020-04-07 13:12 |
VESC Tool | |
|
Vesc120 ADC1 FAIL by sbman on Thu, 2026-07-09 01:41 |
by sbman Thu, 2026-07-09 01:41 |
VESC Tool | ||
|
UART Safety Feature by jaghori.sasan on Wed, 2019-09-04 18:45 |
by jaghori.sasan Wed, 2019-09-04 18:45 |
VESC Tool | ||
|
VESC Partially off Screen by jr226 on Sun, 2023-12-17 20:59 |
1 |
by NOAI Sat, 2024-02-10 14:48 |
VESC Tool |
Pages
