You are here
Active forum topics
Primary tabs
| Topic | Replies | Last post |
Forum |
|
|---|---|---|---|---|
|
Flipsky 6.6 and VESC 5.3 don't mix? by Miniproto on Sun, 2022-11-27 16:34 |
by Miniproto Sun, 2022-11-27 16:34 |
VESC Tool | ||
|
Terminal Command for Current? by Mannerow on Thu, 2020-10-29 23:07 |
by Mannerow Thu, 2020-10-29 23:07 |
VESC Tool | ||
|
FOC is unstable with large Outrunner and had a hardware failure. by SteveBrantley on Tue, 2024-12-31 16:23 |
1 |
by SteveBrantley Wed, 2025-01-01 19:55 |
VESC Tool | |
|
Parameters for efoil by vladek on Thu, 2023-04-20 12:54 |
1 |
by tokerodev Thu, 2025-08-21 11:12 |
VESC Tool | |
|
VESC 75/300 Configuration problems with Hacker Q80 Motors by electricfox on Thu, 2019-02-28 18:23 |
13 |
by Cherry Tue, 2021-01-12 11:56 |
VESC Tool | |
|
Discrepancies between VESC Tool 3.01 Motor Settings & XML config file by j.konrad on Sat, 2022-01-15 22:13 |
3 |
by benjamin Mon, 2022-02-21 22:17 |
VESC Tool | |
|
Newbie question : How to switch to RPM mode ? by Lezard on Thu, 2024-02-29 19:30 |
1 |
by Lezard Mon, 2024-03-11 15:18 |
VESC Tool | |
|
turn counter by player107 on Wed, 2025-09-10 22:52 |
by player107 Wed, 2025-09-10 22:52 |
VESC Tool | ||
|
1.4V noise prevent throttle input mapping by klopped0 on Mon, 2024-07-15 15:24 |
by klopped0 Mon, 2024-07-15 15:24 |
VESC Tool | ||
|
FSESC 6.6 200A Unable to send signal to slave VESC by bms368 on Sat, 2021-02-20 06:16 |
1 |
by adidasgoogle Sun, 2021-03-07 19:11 |
VESC Tool | |
|
Flipsky FSESC 6.7PRO and bluetooth module by phonkie on Mon, 2025-08-18 06:33 |
by phonkie Mon, 2025-08-18 06:33 |
VESC Tool | ||
|
How to update VESC Tool? by Heimfried on Wed, 2020-02-05 10:35 |
2 |
by marialoise Fri, 2020-03-13 20:20 |
VESC Tool | |
|
two motors one ppm for throttle and one for the direction? by Robby Ertmann on Wed, 2021-04-21 13:48 |
by Robby Ertmann Wed, 2021-04-21 13:48 |
VESC Tool | ||
|
Update fail from FW3.58 to 3.61 by sachs2019 on Tue, 2019-09-10 15:51 |
7 |
by AlmaRaposa Thu, 2021-03-11 17:44 |
VESC Tool | |
|
Expert VESC programmer wanted by SGi on Mon, 2023-10-23 01:59 |
1 |
by electricfox Mon, 2023-10-23 09:12 |
VESC Tool | |
|
Updated Firmware on 2 New VESC's says firmware doesnt match when connected by CanBus Cable by vesserik on Mon, 2019-04-08 21:10 |
1 |
by dbell Tue, 2020-12-01 02:14 |
VESC Tool | |
|
TWO MOTOR SYSTEM by ronmotor on Mon, 2022-10-17 00:44 |
by ronmotor Mon, 2022-10-17 00:44 |
VESC Tool | ||
|
Can't update firmware on VESC 6 Firmware 3.54 by tarifachris on Fri, 2025-09-19 02:57 |
by tarifachris Fri, 2025-09-19 02:57 |
VESC Tool | ||
|
VESC 6.05 Fault Coded under Voltage by amblerev on Tue, 2024-07-23 14:37 |
by amblerev Tue, 2024-07-23 14:37 |
VESC Tool | ||
|
[SOLVED] Can I use ADC2 for main throttle control? by oschwartz10612 on Wed, 2021-12-01 22:38 |
3 |
by oschwartz10612 Fri, 2021-12-03 05:08 |
VESC Tool |
Pages
