You are here
Active forum topics
Primary tabs
Topic | Replies | Last post |
Forum![]() |
|
---|---|---|---|---|
Sticky:
Motor Values in VESC-Tool 2019 by frank on Wed, 2019-02-27 09:40 |
19 |
by Onarb Kabr Wed, 2025-01-15 13:28 |
VESC Tool | |
Erpm / torque setting with remote control, Vesc wand by Lasse on Fri, 2021-02-05 22:41 |
1 |
by skyline1970 Tue, 2021-02-09 20:03 |
VESC Tool | |
Position issue by Davideo on Tue, 2017-09-19 16:48 |
3 |
by bOneWheel Mon, 2023-10-30 15:07 |
VESC Tool | |
Setup for very slow < 100RPM on Maytech 6365 Motor. by jason3w on Tue, 2020-09-01 10:52 |
2 |
by asapereira Mon, 2020-09-14 10:26 |
VESC Tool | |
Wrong HW version selected during FW update by babyboi on Sat, 2018-12-15 21:30 |
2 |
by babyboi Sat, 2018-12-22 03:55 |
VESC Tool | |
VESC 4.12 - Current limited at 100A by Laerson on Sun, 2019-09-08 20:23 |
1 |
by benjamin Mon, 2019-09-09 18:20 |
VESC Tool | |
Vesc 1.26 BLE Scan error by huzaini on Mon, 2019-12-16 17:17 |
8 |
by sirAnton Sun, 2020-08-09 15:55 |
VESC Tool | |
How to read the CAN message with CAN anlayzer by yuri12 on Thu, 2022-03-03 18:21 |
by yuri12 Thu, 2022-03-03 18:21 |
VESC Tool | ||
FOC Motor Detection Values Incorrect, PID Tuning Advice? by bmwman91 on Mon, 2020-07-06 03:09 |
by bmwman91 Mon, 2020-07-06 03:21 |
VESC Tool | ||
Step by Step Setup by frank on Wed, 2017-10-04 17:15 |
8 |
by mc Tue, 2018-02-20 11:12 |
VESC Tool | |
From where can I access the FOC code? by vimi94 on Mon, 2019-07-01 14:36 |
1 |
by Teslafly Sat, 2019-07-20 10:31 |
VESC Tool | |
VESC tool windows 10 connection via bluetooth by th0masrtg on Thu, 2020-09-24 14:20 |
11 |
by sp3swj Tue, 2022-03-15 03:08 |
VESC Tool | |
no effect on set erpm/speed limit by xenon321 on Sat, 2021-04-24 20:43 |
by xenon321 Sun, 2021-04-25 16:53 |
VESC Tool | ||
Connect VESC4.7 over USB by Lars_Dierickx on Thu, 2023-03-09 16:13 |
4 |
by Lawrence Sun, 2025-04-27 16:23 |
VESC Tool | |
I Mac Vesc tool !!!! by PHATTY on Fri, 2019-10-11 17:56 |
2 |
by Bender Wed, 2021-03-10 14:39 |
VESC Tool | |
Install VESC on ubuntu 18.04 bionic not working by rest_vesc_001 on Fri, 2020-12-11 18:25 |
1 |
by RitaGilmore Fri, 2021-01-22 16:36 |
VESC Tool | |
single VESC 6+ controlled by CAN-bus by vinci on Fri, 2021-07-09 15:42 |
1 |
by yuri12 Wed, 2022-02-09 17:23 |
VESC Tool | |
Flipsky 6.6 and VESC 5.3 don't mix? by Miniproto on Sun, 2022-11-27 16:34 |
by Miniproto Sun, 2022-11-27 16:34 |
VESC Tool | ||
Download latest VESC Tool version by consti on Wed, 2022-06-15 17:24 |
6 |
by martysmotor Sun, 2025-03-30 11:10 |
VESC Tool | |
Parameters for efoil by vladek on Thu, 2023-04-20 12:54 |
by vladek Thu, 2023-04-20 12:54 |
VESC Tool |
Pages
