You are here
Active forum topics
Primary tabs
| Topic | Replies | Last post |
Forum |
|
|---|---|---|---|---|
|
VESC for EU pedelecs by bb67 on Mon, 2020-04-27 14:11 |
by bb67 Mon, 2020-04-27 14:13 |
General discussion | ||
|
power limited??? by ka_ru on Tue, 2020-11-24 13:53 |
by ka_ru Tue, 2020-11-24 13:53 |
General discussion | ||
|
100V/250A Vesc for sale!!!!! by Fpvlee on Mon, 2021-11-08 03:59 |
2 |
by Svein Utne Fri, 2023-01-20 08:56 |
General discussion | |
|
FAULT_CODE_DRV but find it strange.. by spiderdab on Wed, 2020-11-18 12:18 |
1 |
by masonwilliams Mon, 2020-11-23 11:56 |
General discussion | |
|
GO-FOC G300 - shorted the USB connector shield to 72v by hedbrant on Tue, 2023-04-11 13:22 |
1 |
by hedbrant Thu, 2023-04-13 20:44 |
General discussion | |
|
Question about duty cycle control Vs current control mode by hazzahodgson on Wed, 2026-01-21 08:34 |
by hazzahodgson Wed, 2026-01-21 08:34 |
General discussion | ||
|
Has anyone tried Dc mode by TechAUmNu on Sun, 2018-05-13 14:28 |
4 |
by TechAUmNu Mon, 2018-05-14 15:16 |
General discussion | |
|
Oscillation in FOC current control mode by chris1seto on Fri, 2019-04-05 18:48 |
by chris1seto Fri, 2019-04-05 18:48 |
General discussion | ||
|
Minimum speed push cart using arduino by BarBumble on Wed, 2021-05-12 09:29 |
by BarBumble Wed, 2021-05-12 09:29 |
General discussion | ||
|
Serial Connection Lost with Vesc6.6 Firmware 5.2 and Vesc Tool 3.0 by Dan Slanker on Wed, 2021-04-28 16:56 |
9 |
by AngelKillR Wed, 2022-09-28 05:10 |
General discussion | |
|
Stormcore 60D+ loses drive on one side by Big_McLargeHuge on Wed, 2022-01-26 05:01 |
1 |
by Big_McLargeHuge Wed, 2022-01-26 05:21 |
General discussion | |
|
motors wont turn by Jambi56 on Mon, 2022-09-26 01:48 |
2 |
by Zander rowley Mon, 2023-01-09 16:43 |
General discussion | |
|
advice on position control by feskarn on Mon, 2021-02-15 14:47 |
by feskarn Mon, 2021-02-15 14:47 |
General discussion | ||
|
problem sending with setRPM(float) repeatedly at a high rate by comes04 on Thu, 2023-08-24 14:49 |
by comes04 Thu, 2023-08-24 14:49 |
General discussion | ||
|
Motor won't hold constant speed by Groundspeed100 on Thu, 2024-11-14 05:33 |
by Groundspeed100 Thu, 2024-11-14 05:33 |
General discussion | ||
|
Efficiency Control by devin on Sat, 2018-09-29 19:50 |
19 |
by devin Wed, 2019-07-10 19:35 |
General discussion | |
|
Insufficient torque at low RPM by isso777 on Sat, 2022-04-23 21:13 |
10 |
by frank Tue, 2022-05-03 08:18 |
General discussion | |
|
Compiling in a different config. by Roger Wolff on Mon, 2018-09-17 17:07 |
1 |
by TechAUmNu Mon, 2018-09-17 17:12 |
General discussion | |
|
Something about encoder connection by ztwsa007 on Mon, 2019-07-01 13:43 |
1 |
by ztwsa007 Fri, 2019-07-05 03:26 |
General discussion | |
|
Lehner TorQstar any experience by fabu80 on Wed, 2023-02-01 08:35 |
by fabu80 Wed, 2023-02-01 08:35 |
General discussion |
Pages
