You are here
Active forum topics
Primary tabs
Topic | Replies |
Last post![]() |
Forum | |
---|---|---|---|---|
HIGH Voltage (350v-450v) VESC by athlon on Sun, 2018-11-25 18:34 |
8 |
by Artabotak Wed, 2024-11-27 12:30 |
Third Party Hardware | |
150KW VESC by paltatech on Sun, 2017-09-10 23:11 |
40 |
by Artabotak Wed, 2024-11-27 11:15 |
General discussion | |
position hold below specific duty cycle by lacondro on Wed, 2022-04-27 04:41 |
2 |
by cjmssmd Thu, 2024-11-21 21:29 |
VESC Firmware | |
Balance App Info by NuRxG on Tue, 2020-11-17 21:07 |
1 |
by triff69 Wed, 2024-11-20 10:51 |
Balance App (for EUCs - Electric Unicycles) | |
Dual motor control on VESC6 / 6.00.58 by jediengineer on Mon, 2022-10-10 19:21 |
3 |
by mansi712 Fri, 2024-11-08 20:33 |
VESC Firmware | |
Unbricking a bricked VESC6 - A step by step procedure by espen.oland on Tue, 2020-11-17 18:00 |
2 |
by h1989 Wed, 2024-11-06 06:42 |
VESC Firmware | |
VESC6 firmware update fail by dougm on Fri, 2017-09-01 03:09 |
6 |
by h1989 Tue, 2024-11-05 19:45 |
VESC6 Beta | |
How to read COMM_ROTOR_POSITION through uart by Graham Bowen-Davies on Wed, 2021-04-28 23:59 |
4 |
by mansi712 Tue, 2024-11-05 17:57 |
VESC Tool | |
How can we log all the real time data like motor current, battery current,etc to analyze them later? by vimi94 on Thu, 2019-05-02 09:57 |
27 |
by Stock88 Sun, 2024-11-03 04:02 |
VESC Tool | |
Can't spin both motors over CAN-bus by Kokonenen on Wed, 2023-04-19 11:19 |
4 |
by mansi712 Wed, 2024-10-30 13:40 |
VESC Tool | |
"CAN bus support is not enabled in this build of VESC Tool" by hdfghdfgh on Wed, 2023-04-26 16:13 |
2 |
by mansi712 Mon, 2024-10-28 12:19 |
VESC Tool | |
Old versions of VESC Tool by TheFallen on Thu, 2018-07-05 19:47 |
31 |
by rafeh1 Thu, 2024-10-10 23:44 |
VESC Tool | |
encoder detection error by qdxiatao on Wed, 2018-05-09 12:04 |
1 |
by mona Thu, 2024-10-10 15:55 |
General discussion | |
FOC works, but BLDC doesnt. by knuthcomi on Thu, 2021-03-18 18:31 |
1 |
by EB_Alex Thu, 2024-10-10 04:56 |
Third Party Hardware | |
VESC6 current and duty cycle scale problem? by henry10210 on Sun, 2020-03-29 22:34 |
1 |
by mansi712 Tue, 2024-10-01 12:48 |
VESC Firmware | |
Differential steering setup by GCTech on Sat, 2020-07-04 17:38 |
4 |
by CalLangford Fri, 2024-09-20 20:29 |
General discussion | |
FAULT_CODE_HIGH_OFFSET_CURRENT_SENSOR_3 by TB_Poule on Sat, 2021-04-10 17:26 |
10 |
by Mohanangappan Wed, 2024-09-18 16:20 |
General discussion | |
GPIO Pins on VESC? by phils on Sat, 2022-10-22 17:58 |
2 |
by istvan.szell@gm... Tue, 2024-09-17 12:07 |
General discussion | |
REVERSE FAIL in ADC_CURRENT_REV_BUTTON_BRAKE_ADC by dk-odense on Tue, 2019-12-17 15:45 |
4 |
by Rich235 Fri, 2024-09-13 07:22 |
VESC Firmware | |
VESC 75/300 and EMC Tests for motorcycle conversion by gotfatalErrs on Tue, 2020-06-02 18:34 |
8 |
by Bubu54 Wed, 2024-09-04 13:52 |
General discussion |
Pages
