You are here
Active forum topics
Primary tabs
Topic | Replies |
Last post![]() |
Forum | |
---|---|---|---|---|
Handbrake when activating brake standstill by Pimousse on Mon, 2017-09-11 09:50 |
16 |
by frank Wed, 2019-09-18 16:39 |
Feature Requests | |
I need VESC Tool Version 1.13, please. by Astropower on Sun, 2019-09-08 18:22 |
1 |
by thewho Wed, 2019-09-18 08:29 |
VESC Tool | |
Can't connect to slave vesc via master usb in vesc-tool -SOLVED- by rich on Mon, 2017-07-24 13:31 |
13 |
by fadez Tue, 2019-09-17 14:11 |
VESC6 Beta | |
Problems getting Cruise control to run properly with the new wand - dual VESC6 by MaddiQ on Mon, 2019-09-16 19:36 |
by MaddiQ Mon, 2019-09-16 19:36 |
VESC Firmware | ||
VESC Tool Android - Real-Time Data per controller or combined? by kamikatze13 on Sat, 2019-08-31 22:39 |
1 |
by Stupidspencer Sun, 2019-09-15 19:30 |
VESC Tool | |
wand brake to reverse by michmg on Tue, 2019-09-10 23:54 |
3 |
by michmg Sat, 2019-09-14 20:16 |
General discussion | |
Flipsky VESC 50A by CraigL100 on Fri, 2019-08-30 16:57 |
5 |
by CraigL100 Sat, 2019-09-14 12:10 |
Third Party Hardware | |
Scooter build by waine on Wed, 2019-03-13 17:03 |
1 |
by achinessdirt Sat, 2019-09-14 11:29 |
General discussion | |
Power supply connection for multiple controllers by Caustic_Zinc on Wed, 2019-05-01 21:06 |
1 |
by giganticfizzy Sat, 2019-09-14 10:53 |
General discussion | |
Trapezoidal/ s curve trajectory/"Position Mode" RPM control of BLDC motor by Vishwa Brahmaiah on Fri, 2019-05-24 18:22 |
1 |
by jelliesejecta Sat, 2019-09-14 10:31 |
General discussion | |
Motor not spinning NO FAULTS by 123seaborder on Mon, 2019-06-10 21:46 |
1 |
by gogglespast Sat, 2019-09-14 08:34 |
Third Party Hardware | |
Current Control issue VESC4 by yosoufe on Tue, 2018-03-20 09:28 |
5 |
by itchavenag Fri, 2019-09-13 12:06 |
General discussion | |
Flipsky FSVESC Bricked? by dan.rowe on Thu, 2019-09-12 19:45 |
by dan.rowe Thu, 2019-09-12 19:45 |
Third Party Hardware | ||
VESC to test e-Bike motor and car alternator as Torque Load..? by arifbustani on Thu, 2019-09-12 19:00 |
by arifbustani Thu, 2019-09-12 19:00 |
General discussion | ||
VESC setup in generator application by SaqibBajwa on Fri, 2018-09-21 04:28 |
14 |
by arifbustani Thu, 2019-09-12 18:54 |
VESC Tool | |
FOC bugs by Antoine0106 on Sat, 2019-08-24 18:30 |
2 |
by Stupidspencer Thu, 2019-09-12 17:51 |
General discussion | |
Motor amps higher than batt amps by minim on Sat, 2019-07-06 22:42 |
1 |
by Stupidspencer Mon, 2019-09-09 18:57 |
General discussion | |
VESC 4.12 - Current limited at 100A by Laerson on Sun, 2019-09-08 20:23 |
1 |
by benjamin Mon, 2019-09-09 18:20 |
VESC Tool | |
Can i change the controller (LQFP64) with (LQFP100) with same Firmware? by GalihRiddle on Thu, 2019-09-05 13:44 |
2 |
by GalihRiddle Mon, 2019-09-09 13:22 |
General discussion | |
I need VESC Tool Version 1.13, please. by Astropower on Sun, 2019-09-08 18:22 |
by Astropower Sun, 2019-09-08 18:22 |
VESC Tool |
Pages
