You are here
Active forum topics
Primary tabs
Topic | Replies | Last post | Forum | |
---|---|---|---|---|
Help needed for VESC set up! by mbagrey on Wed, 2018-09-19 22:07 |
3 |
by Roger Wolff Sun, 2018-09-30 16:15 |
VESC Tool | |
Switch two Motor Profiles/Modes (UART) by anli on Thu, 2018-08-16 19:02 |
7 |
by basti30 Sun, 2018-09-30 19:55 |
General discussion | |
Maytech VESC duty cycle & PID control problems by subodh.malgonde on Mon, 2018-10-01 11:49 |
1 |
by subodh.malgonde Tue, 2018-10-02 11:59 |
Third Party Hardware | |
Wiring two VESCs by neuromancer2701 on Mon, 2018-10-01 14:42 |
2 |
by arvidb Wed, 2018-10-03 23:41 |
General discussion | |
VESC for small drone (<1kg) by iKrosoft on Wed, 2018-10-03 16:40 |
3 |
by arvidb Thu, 2018-10-04 21:05 |
General discussion | |
Disable bluetooth. by Roger Wolff on Sun, 2018-10-07 17:06 |
1 |
by arvidb Sun, 2018-10-07 17:27 |
VESC Tool | |
Help with translating/converting hall sensor values from BLDC to FOC by theviith on Thu, 2018-10-11 09:47 |
by theviith Thu, 2018-10-11 09:47 |
General discussion | ||
vesc 4.12 2,3miliohm shunts firmware help by artteth on Sat, 2018-10-13 00:42 |
by artteth Sat, 2018-10-13 00:42 |
VESC Firmware | ||
firmware too old! by ad_brad on Sun, 2018-10-14 18:33 |
1 |
by arvidb Sun, 2018-10-14 19:21 |
VESC Firmware | |
SDRV - Dual 6.4 HW PCB by josh on Wed, 2018-03-07 07:39 |
42 |
by TechAUmNu Mon, 2018-10-15 22:04 |
Third Party Hardware | |
Position Control with Resolver by robo_studienarbeit on Tue, 2018-10-16 18:57 |
by robo_studienarbeit Tue, 2018-10-16 18:57 |
General discussion | ||
How to Traction Control VESC 6 by Karl on Thu, 2018-10-11 03:33 |
2 |
by marti Wed, 2018-10-17 06:02 |
VESC Tool | |
ackmaniac app stopped working ? by badger1666 on Sat, 2018-10-13 12:36 |
1 |
by portnawake Wed, 2018-10-17 08:34 |
General discussion | |
Driving 2 BLDC motors with one MCU by Pimousse on Tue, 2018-06-26 15:42 |
13 |
by wkt Wed, 2018-10-17 14:02 |
Third Party Hardware | |
Vesc is not working by Patryk on Mon, 2018-10-08 18:48 |
4 |
by Patryk Fri, 2018-10-19 22:25 |
General discussion | |
Better use of hall sensors. by ThierryGTLTS on Fri, 2017-10-20 17:18 |
2 |
by AfdhalAtiffTan Wed, 2018-10-24 02:16 |
Feature Requests | |
uart not working on vesc 4.10 latest firmware / hm-10 by daniel84uk on Sat, 2018-09-29 14:55 |
7 |
by acklavidian Wed, 2018-10-24 13:57 |
VESC Firmware | |
FOC Calibration over CAN by thisisjaye on Fri, 2018-10-26 13:15 |
1 |
by frank Fri, 2018-10-26 17:12 |
General discussion | |
PPM valure seems wrong by KKKim on Tue, 2018-10-23 10:56 |
1 |
by frank Fri, 2018-10-26 17:29 |
General discussion | |
dual vesc question by badger1666 on Sun, 2018-10-28 12:59 |
by badger1666 Sun, 2018-10-28 12:59 |
General discussion |