You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
VESC in-air startup failure by jschall on Sat, 2025-04-26 00:56 |
2 |
by jschall Sat, 2025-04-26 01:32 |
General discussion | |
|
Flipsky 75200 Motor ruckelt und wird sehr schnell heiß by Oriessin on Sat, 2025-04-26 07:38 |
by Oriessin Sat, 2025-04-26 07:38 |
General discussion | ||
|
Connect VESC4.7 over USB by Lars_Dierickx on Thu, 2023-03-09 16:13 |
4 |
by Lawrence Sun, 2025-04-27 16:23 |
VESC Tool | |
|
FlipSky 75/300 + Alien 80 KV noise/vibration under load by brendangillatt on Thu, 2021-01-07 01:19 |
13 |
by Thejesh Bollineni Wed, 2025-04-30 22:49 |
General discussion | |
|
UART Servo Output Works in VESC‑Tool UI but Not via ROS Publish by Shreeram2311 on Tue, 2025-05-06 02:40 |
by Shreeram2311 Tue, 2025-05-06 02:40 |
VESC Tool | ||
|
VESC 6 plus working but no servo response by saspragkathos on Mon, 2020-06-29 17:28 |
1 |
by Shreeram2311 Tue, 2025-05-06 02:44 |
VESC Firmware | |
|
Vesc PAS (Pedal Assist) by Evwan on Sat, 2022-07-02 04:37 |
6 |
by wraven Wed, 2025-05-07 14:40 |
VESC Tool | |
|
PID Speed Mode not limiting max ERPM by jordan73s on Sat, 2025-05-03 10:57 |
1 |
by colmor Thu, 2025-05-08 22:44 |
General discussion | |
|
Sensorless Homing: Move motor between two endstops by LISMS on Fri, 2025-05-09 00:50 |
by LISMS Fri, 2025-05-09 00:50 |
Projects incorporating VESC technology | ||
|
Vesc 4.12 USB Issues by puravida13 on Tue, 2025-05-06 18:45 |
1 |
by puravida13 Sat, 2025-05-10 01:53 |
General discussion | |
|
config wanted, for 75100 with ebike geared hub motor by tom355 on Mon, 2023-02-20 09:51 |
3 |
by JanneHooo Sun, 2025-05-11 19:17 |
Third Party Hardware | |
|
VESC hw4.7 firmware update in vesc tool (2.06) fails with "Erase timed out" by snowcrazed on Thu, 2020-07-23 05:47 |
2 |
by Maxid Mon, 2025-05-12 10:27 |
VESC Original Hardware | |
|
VESC Tool Error - updating fw on old hw 4.7 VESCs by sl33py on Sun, 2017-07-09 05:43 |
18 |
by Maxid Mon, 2025-05-12 10:28 |
VESC6 Beta | |
|
Motor seize and ERPM current ramp speed by krabsheva on Tue, 2025-05-13 06:49 |
by krabsheva Tue, 2025-05-13 07:00 |
General discussion | ||
|
Query: Can I run my 70-pole motor using a VESC-based Flipskey controller? by avaid on Thu, 2025-05-08 12:57 |
by avaid Tue, 2025-05-13 08:02 |
General discussion | ||
|
Help needed compiling vesc express for esp32 mini D1 by mrendu43 on Sun, 2023-02-05 18:00 |
3 |
by mvturnho Wed, 2025-05-14 08:46 |
VESC Firmware | |
|
Obarter D5 settings for FSESC75100 by wuzamarine on Sun, 2025-05-11 01:23 |
1 |
by wuzamarine Wed, 2025-05-14 16:23 |
General discussion | |
|
Pole Pairs by donrecardo on Fri, 2020-06-05 10:24 |
4 |
by Bgbalz75 Fri, 2025-05-16 13:01 |
General discussion | |
|
3kw bldc motor (vevor MY1020) + flipsky75100. Cogging and no torque at low speed by Valérian Pigeon on Mon, 2025-04-28 09:50 |
2 |
by Ganzey Mon, 2025-05-19 02:18 |
Projects incorporating VESC technology | |
|
when your third party gives no response? by Jason739 on Sun, 2025-04-27 17:05 |
1 |
by Ganzey Mon, 2025-05-19 02:21 |
Third Party Hardware |
Pages
