You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
AS5048A and the AS5047D Problems. by raess on Wed, 2018-04-04 14:05 |
2 |
by liqikai Thu, 2018-09-13 10:47 |
General discussion | |
|
FOC detection needs load? by tuloski on Thu, 2018-09-13 10:19 |
1 |
by TechAUmNu Thu, 2018-09-13 12:26 |
VESC Tool | |
|
Cut-out at >40A by thewho on Thu, 2018-09-13 20:24 |
by thewho Thu, 2018-09-13 20:24 |
General discussion | ||
|
Maytech esc 5V rail reads 0.5v by hhhhghg on Fri, 2018-09-14 13:23 |
by hhhhghg Fri, 2018-09-14 13:23 |
Third Party Hardware | ||
|
FAULT_CODE_DRV Motor not spinning by Mightyorc on Sat, 2018-09-15 03:36 |
by Mightyorc Sat, 2018-09-15 03:36 |
General discussion | ||
|
Speed control tuning for 500-1000 RPM by vadimz on Sun, 2018-09-02 18:09 |
2 |
by vadimz Sat, 2018-09-15 14:08 |
General discussion | |
|
Show actual encoder RPM by Enak on Fri, 2017-09-08 01:05 |
2 |
by Roger Wolff Sun, 2018-09-16 09:47 |
Feature Requests | |
|
VESC Tool 0.87 by pieschie on Sun, 2018-08-26 12:38 |
3 |
by Roger Wolff Sun, 2018-09-16 12:00 |
VESC Tool | |
|
Compiling in a different config. by Roger Wolff on Mon, 2018-09-17 17:07 |
1 |
by TechAUmNu Mon, 2018-09-17 17:12 |
General discussion | |
|
Problems with a small motor by tuloski on Thu, 2018-09-13 17:27 |
3 |
by tuloski Mon, 2018-09-17 18:21 |
VESC Firmware | |
|
Custom 12S VESC seems to be power limiting or something by nickw1881 on Sat, 2018-08-25 07:40 |
4 |
by nickw1881 Tue, 2018-09-18 05:56 |
Third Party Hardware | |
|
HW 4.12 Change low voltage cutoff by subodh.malgonde on Tue, 2018-09-18 07:31 |
7 |
by TheFallen Thu, 2018-09-20 09:51 |
VESC Original Hardware | |
|
Maytech VESC keeps startup spinning slowly by Snorreman on Mon, 2018-09-24 09:57 |
by Snorreman Mon, 2018-09-24 09:57 |
Third Party Hardware | ||
|
Maytech VESC 4.10 UART issues by LogixCraft on Tue, 2018-09-25 03:13 |
by LogixCraft Tue, 2018-09-25 03:13 |
Third Party Hardware | ||
|
PYVESC UART Issues by goethe on Fri, 2017-12-29 21:36 |
13 |
by petertaylor Tue, 2018-09-25 10:06 |
VESC Firmware | |
|
dual vesc by badger1666 on Fri, 2018-09-21 09:10 |
4 |
by badger1666 Sat, 2018-09-29 15:45 |
General discussion | |
|
Help needed for VESC set up! by mbagrey on Wed, 2018-09-19 22:07 |
3 |
by Roger Wolff Sun, 2018-09-30 16:15 |
VESC Tool | |
|
Switch two Motor Profiles/Modes (UART) by anli on Thu, 2018-08-16 19:02 |
7 |
by basti30 Sun, 2018-09-30 19:55 |
General discussion | |
|
Maytech VESC duty cycle & PID control problems by subodh.malgonde on Mon, 2018-10-01 11:49 |
1 |
by subodh.malgonde Tue, 2018-10-02 11:59 |
Third Party Hardware | |
|
Wiring two VESCs by neuromancer2701 on Mon, 2018-10-01 14:42 |
2 |
by arvidb Wed, 2018-10-03 23:41 |
General discussion |
Pages
