You are here
Active forum topics
Primary tabs
Topic | Replies | Last post | Forum | |
---|---|---|---|---|
Profiles with dual 75100 for 2wd recumbent trike by khallie06 on Tue, 2024-10-01 01:44 |
2 |
by Onarb Kabr Mon, 2024-11-25 13:37 |
General discussion | |
VESC crashes on Servo output by AutonomousDrifting on Fri, 2021-02-05 13:25 |
6 |
by Onarb Kabr Mon, 2024-11-25 13:40 |
General discussion | |
Help needed VESC - Update missed? by JUST1975 on Tue, 2024-11-26 11:43 |
1 |
by JUST1975 Tue, 2024-11-26 11:53 |
VESC Firmware | |
150KW VESC by paltatech on Sun, 2017-09-10 23:11 |
40 |
by Artabotak Wed, 2024-11-27 11:15 |
General discussion | |
HIGH Voltage (350v-450v) VESC by athlon on Sun, 2018-11-25 18:34 |
8 |
by Artabotak Wed, 2024-11-27 12:30 |
Third Party Hardware | |
Makerbase VESC 84200HP It won't turn on. by Deejii23 on Sun, 2024-11-24 16:31 |
1 |
by Deejii23 Thu, 2024-11-28 18:58 |
Third Party Hardware | |
Someone please help by Mark griffin on Thu, 2024-08-01 14:29 |
2 |
by Onarb Kabr Sun, 2024-12-01 17:20 |
General discussion | |
Can’t connect VESC tool to my ESC. Pls help by Comeback10 on Mon, 2024-09-16 23:08 |
1 |
by Onarb Kabr Sun, 2024-12-01 17:21 |
General discussion | |
SINE/COS encoder makes motor not work by DHOUT on Mon, 2023-01-30 05:23 |
1 |
by Jamesstudio Sun, 2024-12-01 17:56 |
General discussion | |
VESC Tool Device UI not shown on Raspberry Pi/Linux by Sebastiaan Koning on Mon, 2024-12-02 13:19 |
by Sebastiaan Koning Mon, 2024-12-02 13:19 |
VESC Tool | ||
wrong amps reading (realtime data) by flez1966 on Wed, 2024-03-27 13:55 |
2 |
by B1996 Tue, 2024-12-03 07:26 |
Third Party Hardware | |
position control with gearbox by raess on Tue, 2018-09-25 23:48 |
19 |
by Artabotak Tue, 2024-12-03 08:48 |
General discussion | |
Tach output changes when switching from BLDC --> FOC by Zoxks on Sun, 2024-12-01 20:28 |
1 |
by Zoxks Tue, 2024-12-03 19:10 |
General discussion | |
VESC 4.7 old firmware update issue by Lars_Dierickx on Sun, 2023-03-19 15:39 |
4 |
by konabiker Wed, 2024-12-04 11:45 |
VESC Firmware | |
Spintend v2 100amp 100volt by Phill Dixon on Wed, 2024-12-04 18:14 |
1 |
by electricfox Wed, 2024-12-04 20:06 |
General discussion | |
firmware V6.06 vs VESC tool V6.05 by shuang on Thu, 2024-12-05 06:49 |
by shuang Thu, 2024-12-05 06:49 |
VESC Firmware | ||
How to prevent ground loop? by mansi712 on Fri, 2024-11-01 17:46 |
3 |
by Spaceman Thu, 2024-12-05 14:23 |
General discussion |