You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
Acceleration control to desired RPM by bjohns on Fri, 2018-07-20 22:08 |
9 |
by arvidb Thu, 2018-08-09 21:15 |
General discussion | |
|
STM32F302 based? by darkkat on Wed, 2018-08-08 11:52 |
1 |
by Danny Bokma Fri, 2018-08-10 07:05 |
VESC Firmware | |
|
Raw encoder output from UART by sprockmonty on Mon, 2018-08-13 16:45 |
by sprockmonty Mon, 2018-08-13 16:45 |
Feature Requests | ||
|
Uploaded Firmware, Not Updated by kneave on Sat, 2018-08-18 21:02 |
2 |
by kneave Sat, 2018-08-18 21:48 |
VESC Firmware | |
|
Adding capacitors with long power cables? by rich on Thu, 2017-09-07 20:40 |
6 |
by frank Mon, 2018-08-20 09:12 |
VESC Original Hardware | |
|
VESC 6 With AS5047 encoder by Geir Henriksen on Tue, 2018-07-31 00:09 |
2 |
by frank Mon, 2018-08-20 09:32 |
Third Party Hardware | |
|
Hub motor FOC detection. by Roger Wolff on Tue, 2018-08-21 19:12 |
by Roger Wolff Tue, 2018-08-21 19:12 |
General discussion | ||
|
VESC Software Understanding by shubhamt on Wed, 2018-08-22 15:40 |
by shubhamt Wed, 2018-08-22 15:40 |
General discussion | ||
|
Set McConf with no values --> bootloader erased? by Kakskiv on Tue, 2017-11-28 12:52 |
3 |
by basti30 Wed, 2018-08-22 22:22 |
General discussion | |
|
Motor temperature, how to set limit >120 C ? by RSR on Wed, 2018-08-22 12:40 |
3 |
by Danny Bokma Thu, 2018-08-23 07:19 |
VESC Tool | |
|
single micro multiple driver support by Robert lloyd on Thu, 2018-07-26 11:58 |
3 |
by TheFallen Thu, 2018-08-23 10:08 |
VESC Firmware | |
|
hall sensor calibration. by Roger Wolff on Mon, 2018-04-16 11:17 |
5 |
by svs Mon, 2018-08-27 13:34 |
General discussion | |
|
4.12 HK VESC - Static blue LED and no usb Connection, HELP!! by plot1992 on Thu, 2018-08-02 19:01 |
5 |
by Frazatto Tue, 2018-08-28 15:43 |
General discussion | |
|
What temerpature sensor and how do I use it? by evoheyax on Wed, 2018-08-29 19:22 |
3 |
by Danny Bokma Thu, 2018-08-30 19:12 |
General discussion | |
|
Firmware for Hardware V6 by EU-Sampler on Fri, 2018-08-31 08:50 |
1 |
by Danny Bokma Fri, 2018-08-31 13:16 |
VESC Firmware | |
|
Ramping and idle control by dougm on Sat, 2018-09-01 16:22 |
by dougm Sat, 2018-09-01 16:22 |
Feature Requests | ||
|
Serial port error when Encoder detection is complete by VirtB on Wed, 2018-08-29 03:03 |
3 |
by VirtB Sun, 2018-09-02 03:33 |
VESC Tool | |
|
How to read MotorRPM from UART to Arduino by azobe on Thu, 2018-03-08 14:42 |
3 |
by Pimousse Mon, 2018-09-03 14:31 |
General discussion | |
|
Move FAULT pin to GPIOD_PIN2 by CTSchorsch on Tue, 2018-09-04 10:13 |
by CTSchorsch Tue, 2018-09-04 10:13 |
VESC Firmware | ||
|
How to erase whole flash with OpenOCD? by Frazatto on Mon, 2018-09-03 14:56 |
1 |
by Frazatto Tue, 2018-09-04 19:33 |
General discussion |
Pages
