You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
Vesc4 have 2 Analog output pins? by greensightag.com on Sat, 2018-05-12 00:42 |
1 |
by Roger Wolff Tue, 2018-05-15 10:51 |
VESC Original Hardware | |
|
Cruise Control Button while using UART? by anli on Tue, 2018-05-15 16:08 |
3 |
by Tilman Baumann Wed, 2018-05-16 15:31 |
VESC Firmware | |
|
How to make VESC 4.12 can work with 14S batteries? by Ken_chen on Sat, 2018-04-21 04:39 |
5 |
by Roger Wolff Sun, 2018-05-20 08:36 |
General discussion | |
|
Bricked my VESC six what now? by atat on Sun, 2018-05-20 13:07 |
by atat Sun, 2018-05-20 14:28 |
General discussion | ||
|
Phase current limit mismatch by Addy on Tue, 2018-05-22 17:12 |
by Addy Tue, 2018-05-22 17:12 |
VESC Firmware | ||
|
VESC error with red lights flshing 4 times by yingsy on Thu, 2018-05-17 05:11 |
1 |
by hexakopter Wed, 2018-05-23 11:18 |
General discussion | |
|
Should I drive a HDD motor with VESC or some other chip? by arildj78 on Tue, 2018-05-22 09:09 |
1 |
by arildj78 Wed, 2018-05-23 12:26 |
General discussion | |
|
Throttle curves by Phill Dixon on Wed, 2018-05-23 18:16 |
1 |
by Tilman Baumann Thu, 2018-05-24 11:33 |
General discussion | |
|
BitWizard ESC thermal Mod 100A cont. by Philipp Spindler on Thu, 2018-05-24 16:01 |
3 |
by Roger Wolff Thu, 2018-05-24 18:10 |
Third Party Hardware | |
|
FOC detection.... by Roger Wolff on Thu, 2018-05-24 17:37 |
3 |
by TechAUmNu Sun, 2018-05-27 21:14 |
VESC Tool | |
|
Input Voltage on PPM (Servo) VESC6? by Marc Pflugmann on Fri, 2018-05-25 21:02 |
3 |
by Roger Wolff Thu, 2018-05-31 08:05 |
VESC Original Hardware | |
|
FFT in VESC Tool by RSR on Thu, 2018-05-31 14:37 |
3 |
by TechAUmNu Thu, 2018-05-31 16:28 |
VESC Tool | |
|
Getting started with bus control of the VESC by Invert on Mon, 2018-05-21 12:04 |
3 |
by PM Thu, 2018-05-31 18:38 |
General discussion | |
|
Inappropriate ioctl by Roger Wolff on Sat, 2018-06-02 17:38 |
by Roger Wolff Sat, 2018-06-02 18:04 |
VESC Tool | ||
|
VESC 6.4 supplys Arduino over SIGNAL!! by MaxMaker1 on Thu, 2018-05-24 15:02 |
4 |
by frank Mon, 2018-06-04 23:24 |
VESC Original Hardware | |
|
PWM length not correctly measured by ufechner on Tue, 2018-06-05 11:45 |
by ufechner Tue, 2018-06-05 11:45 |
VESC Firmware | ||
|
How to access VESC error codes in the new VESC tool by berno3 on Tue, 2018-06-05 08:47 |
1 |
by Roger Wolff Wed, 2018-06-06 07:36 |
VESC Tool | |
|
Removing low speed openloop FOC parking brake mode from FW by rodread on Thu, 2018-03-08 15:01 |
4 |
by arvidb Wed, 2018-06-06 19:02 |
General discussion | |
|
150KW VESC by paltatech on Sun, 2017-09-10 23:11 |
39 |
by paltatech Fri, 2018-06-08 20:02 |
General discussion | |
|
[SOLVED]Motors "blocking totally" when throttling, after running VESC setup. by MaddiQ on Tue, 2018-06-12 21:01 |
by MaddiQ Tue, 2018-06-12 23:36 |
General discussion |
Pages
