You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
Problem to configure my esc with PWM-signal by Lucar on Wed, 2022-09-14 10:05 |
1 |
by skyline1970 Thu, 2022-11-24 20:26 |
VESC Tool | |
|
VESC - HIL / DRV8301 SPI - Problems? by mm_iem on Tue, 2022-08-09 12:34 |
1 |
by skyline1970 Thu, 2022-11-24 20:54 |
VESC Firmware | |
|
Open ESC for sensored 1/12 pan cars? by DocTrucker on Tue, 2022-08-02 08:33 |
1 |
by skyline1970 Thu, 2022-11-24 21:02 |
General discussion | |
|
Hall effect sensor type for Flipsky 4.20 by braydinjones on Sun, 2022-07-24 01:06 |
1 |
by skyline1970 Thu, 2022-11-24 21:06 |
General discussion | |
|
Fault code sensor 1 by krille on Sat, 2022-07-23 16:31 |
1 |
by skyline1970 Thu, 2022-11-24 21:08 |
General discussion | |
|
VESC as voltage regulator in hybrid UAV by Bunda on Sun, 2022-07-10 08:01 |
1 |
by skyline1970 Thu, 2022-11-24 21:19 |
General discussion | |
|
FSESC 75100 repair by BDJ on Fri, 2022-06-24 21:02 |
1 |
by skyline1970 Thu, 2022-11-24 21:22 |
General discussion | |
|
Taking 5-6 seconds for running motor under ADC mode by asnamp on Fri, 2022-06-24 13:02 |
1 |
by skyline1970 Thu, 2022-11-24 21:24 |
VESC Tool | |
|
Controller voor BLDC motor by Kapitein Nelson on Fri, 2022-04-29 17:26 |
1 |
by skyline1970 Thu, 2022-11-24 21:31 |
General discussion | |
|
Controller bricked after firmware update how to recover by ardillolambo on Sat, 2022-04-30 15:31 |
1 |
by skyline1970 Thu, 2022-11-24 21:35 |
VESC Firmware | |
|
Can't start a sensorless motor of a scooter by tobe81cwb on Mon, 2022-05-02 03:25 |
1 |
by skyline1970 Thu, 2022-11-24 21:36 |
General discussion | |
|
SETUP FOR SINGLE BRUSHED MOTOR by mmatthews@aquav... on Fri, 2022-05-13 01:57 |
1 |
by skyline1970 Thu, 2022-11-24 21:39 |
General discussion | |
|
drill batteries in series with Flipsky 75100 by alexkid on Sat, 2022-05-14 15:41 |
1 |
by skyline1970 Thu, 2022-11-24 21:41 |
General discussion | |
|
MAX40056F as INA240 alternative by Max2 on Sun, 2022-05-08 01:03 |
1 |
by skyline1970 Thu, 2022-11-24 21:43 |
VESC6 Beta | |
|
VESC 6 Plus reseting settings and firmware by granstubbe on Fri, 2020-01-10 18:31 |
2 |
by ozcankosar Fri, 2022-11-25 22:18 |
VESC Original Hardware | |
|
Motor always accelerates to maximum speed by zapshe on Sun, 2022-09-11 03:46 |
1 |
by skyline1970 Sun, 2022-11-27 16:32 |
VESC Tool | |
|
Flipsky 6.6 and VESC 5.3 don't mix? by Miniproto on Sun, 2022-11-27 16:34 |
by Miniproto Sun, 2022-11-27 16:34 |
VESC Tool | ||
|
Cannot connect to vesc tool app by sharpshooterjd on Fri, 2022-07-29 23:39 |
1 |
by skyline1970 Sun, 2022-11-27 16:38 |
VESC Tool | |
|
Serial Control From PC by aguzel on Fri, 2020-08-21 02:45 |
3 |
by Jens Mon, 2022-11-28 20:40 |
VESC Tool | |
|
help - vesc tool configure for edf turbine D3541 1450KV 6s DoBoFo by Everton C on Tue, 2022-11-29 15:45 |
1 |
by frank Tue, 2022-11-29 17:52 |
General discussion |
Pages
