You are here

Active forum topics

Topic Replies Last postsort descending Forum
Normal topic Lanyard kill switch
by craig w on Mon, 2022-01-03 09:30
3 by ewakegermanyhq
Wed, 2022-08-03 16:55
General discussion
Normal topic Different rpm when using 3 vesc with can-bus
by ewakegermanyhq on Wed, 2022-08-03 17:03
by ewakegermanyhq
Wed, 2022-08-03 17:03
VESC Tool
Normal topic VESC Setup - Fluctuating/Unstable Duty Cycle/eRPM/Current
by liminalsunset on Thu, 2022-08-04 01:44
by liminalsunset
Thu, 2022-08-04 01:44
General discussion
Normal topic FAULT_CODE_UNDER_VOLTAGE
by alexantosh on Mon, 2021-11-29 09:26
9 by heravinluca
Thu, 2022-08-04 04:19
VESC Tool
Normal topic temperature compensation make sense?
by alexshen2012 on Thu, 2022-08-04 08:28
1 by alexshen2012
Thu, 2022-08-04 09:17
General discussion
Normal topic Updated VESC 6 schematic request
by ma-j-sterelektron on Mon, 2019-03-25 08:43
3 by Roby_88
Thu, 2022-08-04 12:43
General discussion
Normal topic Tips on tuning PID for a 170mm RW170 hub motor, 15 pole-pairs, low speed, high torque, 0-3000 ERPM
by PaulMakesThings on Fri, 2022-08-05 11:06
by PaulMakesThings
Fri, 2022-08-05 11:06
General discussion
Normal topic Help with a settings for only generator
by Mafo on Fri, 2018-03-02 16:59
7 by JP
Fri, 2022-08-05 11:50
VESC Tool
Normal topic I'm so new to this. Question about the G4 series capabilities
by betacyth on Fri, 2022-08-05 19:51
by betacyth
Fri, 2022-08-05 19:51
VESC Development and Beta Testing
Normal topic Internal Data Logging
by KS0n on Thu, 2018-01-11 19:58
5 by mrendu43
Sat, 2022-08-06 09:36
Feature Requests
Normal topic the latest vesc6 version
by Andy Moon on Wed, 2021-07-21 11:00
1 by Sybervenon
Sat, 2022-08-06 22:05
VESC Development and Beta Testing
Normal topic iq sign reversal at high RPM (was: Duty cycle jumps to maximum when *lowering* current limit)
by vadimz on Thu, 2022-06-23 14:00
4 by vadimz
Sun, 2022-08-07 13:03
VESC Firmware
Normal topic Flipsky 75100 with Flipsky VX1 remote -- do I have the wiring right? (VESC4 connector)
by SeguinM on Sun, 2022-08-07 15:32
by SeguinM
Sun, 2022-08-07 15:32
Third Party Hardware
Normal topic KV command in terminal ( how to determine kv of a motor )
by fessyfoo on Sat, 2020-05-09 21:21
1 by rafeh1
Mon, 2022-08-08 04:31
VESC Tool
Normal topic VESC 6.0 Data Logging?
by josh on Fri, 2017-06-30 00:00
12 by aaron1010
Mon, 2022-08-08 05:38
VESC6 Beta
Normal topic step/dir
by blueflower on Thu, 2020-01-16 04:15
5 by akkoxe
Mon, 2022-08-08 06:34
General discussion
Normal topic Can you switch censored to sensor less or HFI
by diyRick on Wed, 2021-06-30 23:43
3 by Erick45
Mon, 2022-08-08 13:01
General discussion
Normal topic Axial Flux motor control mode
by ardillolambo on Wed, 2022-03-02 13:59
5 by gemmalyly
Tue, 2022-08-09 04:16
VESC Original Hardware
Normal topic VESC - HIL / DRV8301 SPI - Problems?
by mm_iem on Tue, 2022-08-09 12:34
by mm_iem
Tue, 2022-08-09 12:41
VESC Firmware
Normal topic Flipsky 75100 rebooting under load
by SpacePT on Tue, 2022-07-26 14:47
1 by loyevaquez
Wed, 2022-08-10 09:48
Third Party Hardware

Pages

Subscribe to Active forum topics