You are here
Active forum topics
Primary tabs
Topic | Replies | Last post | Forum | |
---|---|---|---|---|
VESC with auto calibration of grace one motor (videos included) by ligi on Mon, 2020-10-19 02:13 |
10 |
by ligi Tue, 2020-11-17 06:56 |
General discussion | |
VESC Questions from the newbie by mendez on Fri, 2019-02-08 21:13 |
10 |
by frank Mon, 2019-02-18 08:52 |
General discussion | |
First impressions to the new VESC Tool software by hexakopter on Fri, 2017-05-26 21:19 |
10 |
by Roger Wolff Sun, 2017-06-11 06:27 |
VESC6 Beta | |
FAULT_CODE_ABS_OVER_CURRENT on custom pcb by TVAVAE on Sat, 2021-07-10 00:44 |
9 |
by hakan seray Wed, 2022-06-15 12:27 |
Third Party Hardware | |
Flux linkage observer @ low speed by soltesz on Sun, 2017-12-17 16:33 |
9 |
by benjamin Thu, 2017-12-21 10:17 |
VESC Firmware | |
VESC settings for large scooter motor by trimen on Tue, 2020-07-14 22:15 |
9 |
by pwn1j Tue, 2024-07-02 23:30 |
General discussion | |
IGBT Vesc FOC not working by ziumus on Sat, 2019-09-28 15:48 |
9 |
by bgdwiepp Sat, 2019-10-19 21:56 |
Third Party Hardware | |
Problem with burned FETs and drivers after reconnect battery by CTSchorsch on Sat, 2021-01-16 19:49 |
9 |
by CTSchorsch Wed, 2021-02-17 13:42 |
Third Party Hardware | |
15S support (and more amps) by Torxed on Mon, 2018-07-16 12:06 |
9 |
by Torxed Sat, 2018-07-21 21:52 |
Feature Requests | |
Acceleration control to desired RPM by bjohns on Fri, 2018-07-20 22:08 |
9 |
by arvidb Thu, 2018-08-09 21:15 |
General discussion | |
Serial Connection Lost with Vesc6.6 Firmware 5.2 and Vesc Tool 3.0 by Dan Slanker on Wed, 2021-04-28 16:56 |
9 |
by AngelKillR Wed, 2022-09-28 05:10 |
General discussion | |
FAULT_CODE_UNDER_VOLTAGE by alexantosh on Mon, 2021-11-29 09:26 |
9 |
by heravinluca Thu, 2022-08-04 04:19 |
VESC Tool | |
Help is there an issue with my new Vesc 6 by avis on Sat, 2017-09-30 15:21 |
9 |
by frank Wed, 2017-10-04 17:10 |
General discussion | |
vesc tool 1.25 not opening. by osis on Tue, 2019-10-29 20:50 |
9 |
by flyingbrike Wed, 2021-09-08 09:06 |
VESC Tool | |
Failure in Motor Set Up by Toshi Sharma on Tue, 2022-01-11 15:19 |
9 |
by frank Thu, 2022-01-13 14:15 |
General discussion | |
VESC Tool wont start by w31x on Wed, 2020-03-11 19:30 |
9 |
by SUB13 Sun, 2024-02-11 14:43 |
VESC Tool | |
Invert motor direction. by Sanjoy on Thu, 2017-06-15 23:31 |
9 |
by Roger Wolff Mon, 2017-06-19 16:00 |
VESC6 Beta | |
VESC with Raspberry Pi 3 by Antonio Rodrígu... on Sun, 2018-06-03 18:54 |
9 |
by ShortCircuit Thu, 2018-06-28 15:33 |
General discussion | |
(solved) Configuration smooth motordirection change by horak2084 on Mon, 2019-02-25 20:44 |
9 |
by fpagac Sat, 2020-04-25 17:17 |
VESC Firmware | |
Setting PI / PID controllers in VESC for very low speeds. For CNC by K@RLSON on Sat, 2020-01-25 21:06 |
9 |
by Luke264 Wed, 2021-02-17 18:52 |
General discussion |