You are here
Active forum topics
Primary tabs
Topic |
Replies![]() |
Last post | Forum | |
---|---|---|---|---|
VESC-Tool Bugs by Danny Bokma on Sun, 2017-06-04 01:44 |
13 |
by sevenfloorsdown Wed, 2022-03-23 22:45 |
VESC6 Beta | |
Driving 2 BLDC motors with one MCU by Pimousse on Tue, 2018-06-26 15:42 |
13 |
by wkt Wed, 2018-10-17 14:02 |
Third Party Hardware | |
Can't connect to slave vesc via master usb in vesc-tool -SOLVED- by rich on Mon, 2017-07-24 13:31 |
13 |
by fadez Tue, 2019-09-17 14:11 |
VESC6 Beta | |
2 vs 3 phase shunts by antonchromjak on Sun, 2018-04-15 13:25 |
13 |
by TechAUmNu Fri, 2019-02-15 18:57 |
General discussion | |
Factors of VESC motor detection and operation with 3rd Party Hardware by shaman on Wed, 2020-04-01 20:44 |
13 |
by vadicus Wed, 2020-05-13 00:23 |
General discussion | |
Two VESCs, two three-phase windings, one motor stator by kubark42 on Fri, 2021-11-12 21:29 |
13 |
by skyline1970 Fri, 2021-11-19 20:05 |
General discussion | |
The selected file is too large to be a firmware. by vinci on Wed, 2022-04-20 18:50 |
13 |
by makentor Thu, 2022-12-08 18:19 |
VESC Firmware | |
swagatron hoverboard motors with VESC by popeye243 on Tue, 2020-07-21 02:49 |
13 |
by popeye243 Mon, 2020-09-07 03:42 |
General discussion | |
PYVESC UART Issues by goethe on Fri, 2017-12-29 21:36 |
13 |
by petertaylor Tue, 2018-09-25 10:06 |
VESC Firmware | |
VESC 75/300 Configuration problems with Hacker Q80 Motors by electricfox on Thu, 2019-02-28 18:23 |
13 |
by Cherry Tue, 2021-01-12 11:56 |
VESC Tool | |
Trying to connect over USB, but new 6.4 connects and disconnects a few seconds later. by MaxMaker1 on Thu, 2018-05-24 16:15 |
12 |
by frank Thu, 2019-02-21 20:34 |
VESC Tool | |
FSESC 6.6 not Connecting to VESC Tool by billyredwood01 on Sat, 2020-11-28 12:34 |
12 |
by JP Mon, 2023-04-03 13:02 |
General discussion | |
Hoverboard Motor with VESC by mados73 on Wed, 2018-03-21 22:14 |
12 |
by Kirkness Mon, 2020-07-13 01:00 |
General discussion | |
Experience with QS120 IPM motor? by marvinrau on Mon, 2021-05-31 14:03 |
12 |
by pe Tue, 2021-11-16 18:20 |
General discussion | |
ADC pin voltage not zero by zoppp on Fri, 2019-02-08 23:44 |
12 |
by zoppp Tue, 2019-03-12 01:17 |
General discussion | |
temp motor by emmaanuel on Wed, 2017-09-13 01:27 |
12 |
by Roger Wolff Wed, 2017-11-08 16:23 |
VESC Firmware | |
Adjusting Beta Value for Motor Thermistor. by Ecyclist on Thu, 2018-12-06 23:22 |
12 |
by Ecyclist Tue, 2019-01-29 04:29 |
VESC Tool | |
Motors spin up during detection but then won't move by jordan314 on Thu, 2019-02-21 09:18 |
12 |
by KDoc Tue, 2023-01-17 00:13 |
VESC Tool | |
FOC with encoder by Ledz on Tue, 2018-05-15 11:55 |
12 |
by Ramesh Thu, 2023-12-21 07:22 |
General discussion | |
Realtime time axis by Eric on Tue, 2017-09-05 14:29 |
12 |
by hexakopter Mon, 2017-10-23 20:23 |
VESC Tool |
Pages
