You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
DRV8302 Gate Pin output waveform is abnormal by yandongyu1998 on Fri, 2019-12-13 07:21 |
by yandongyu1998 Fri, 2019-12-13 07:21 |
General discussion | ||
|
Configuration of underwater thruster by UnderwaterMotors on Fri, 2023-03-24 18:10 |
by UnderwaterMotors Fri, 2023-03-24 18:10 |
General discussion | ||
|
aggressive throttle by Sandro luis on Sun, 2024-05-05 04:42 |
by Sandro luis Sun, 2024-05-05 04:42 |
General discussion | ||
|
no effect on set erpm/speed limit by xenon321 on Sat, 2021-04-24 20:43 |
by xenon321 Sun, 2021-04-25 16:53 |
VESC Tool | ||
|
sick srm50 absolute encoder, I don't know how to configure it by Davidson SIlvei... on Mon, 2024-04-22 21:45 |
by Davidson SIlvei... Mon, 2024-04-22 21:45 |
VESC Tool | ||
|
Custom-made VESC PCB: High current sensor offset/Overcurrent fault during motor detection, possible hardware/firmware mismatch by Chinmay Mulgund on Mon, 2025-10-13 13:56 |
by Chinmay Mulgund Mon, 2025-10-13 14:02 |
General discussion | ||
|
Maytech VESC 4.10 UART issues by LogixCraft on Tue, 2018-09-25 03:13 |
by LogixCraft Tue, 2018-09-25 03:13 |
Third Party Hardware | ||
|
Stream UART Telemetry without a Request by AlexBenn on Thu, 2022-01-20 02:47 |
by AlexBenn Thu, 2022-01-20 02:47 |
VESC Firmware | ||
|
VESC 75/300 singnal connectors by Mikko Valtonen on Tue, 2020-05-19 21:43 |
by Mikko Valtonen Tue, 2020-05-19 21:43 |
VESC Original Hardware | ||
|
Wheel speed over CANBUS by paule on Tue, 2020-12-29 13:04 |
by paule Tue, 2020-12-29 13:04 |
General discussion | ||
|
vesc setup 42V 10A e-bike accu to build in a E-skatboard by olaf2273 on Fri, 2020-04-10 12:33 |
by olaf2273 Mon, 2020-04-27 15:34 |
General discussion | ||
|
Setting RPM over UART by klay2000 on Sat, 2024-06-29 01:27 |
by klay2000 Sat, 2024-06-29 01:28 |
General discussion | ||
|
Bug? by arxera on Sat, 2026-04-04 12:34 |
by arxera Sat, 2026-04-04 12:34 |
VESC Tool | ||
|
Remap Rotary Encoder Input to CAN (or other) by Artemis Skade on Wed, 2020-04-01 20:23 |
by Artemis Skade Wed, 2020-04-01 20:23 |
Feature Requests | ||
|
MakerX-FOC DV6s PWM for 2 BLDC Motors by paulsimpsonii on Tue, 2026-03-03 18:08 |
by paulsimpsonii Tue, 2026-03-03 18:08 |
General discussion | ||
|
BLDC zero cross happens too early by Sgw32 on Thu, 2021-05-20 19:10 |
by Sgw32 Thu, 2021-05-20 19:10 |
General discussion | ||
|
reverse programing by axialflux on Mon, 2023-11-13 23:21 |
by axialflux Mon, 2023-11-13 23:21 |
General discussion | ||
|
Dual Motor Setup not working via CAN Bus (solved) by acleon on Fri, 2020-06-19 00:03 |
by acleon Fri, 2020-06-19 16:33 |
VESC Tool | ||
|
Regarding code documentation by hiddenzed on Mon, 2021-02-08 12:40 |
by hiddenzed Mon, 2021-02-08 12:40 |
VESC Firmware | ||
|
Using vesc for real time gps tracking, alarm and data recorder by Nicolas Durandet on Sun, 2023-10-22 14:56 |
by Nicolas Durandet Sun, 2023-10-22 14:56 |
General discussion |
Pages
