You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
75/300 R3 Power ON/OFF PINs and LED Status by nice2cu on Wed, 2020-06-17 17:35 |
by nice2cu Wed, 2020-06-17 17:37 |
VESC Original Hardware | ||
|
DRV Fault at high load by mikoyas on Sat, 2020-06-13 15:43 |
by mikoyas Sat, 2020-06-13 15:43 |
General discussion | ||
|
dual VESC battery current by chris_winkel on Tue, 2019-06-18 15:26 |
by chris_winkel Tue, 2019-06-18 15:26 |
VESC Original Hardware | ||
|
Access denied when trying to connect by Robban on Sun, 2021-09-12 14:30 |
by Robban Sun, 2021-09-12 14:30 |
General discussion | ||
|
Firmware upgrade from 3.38 not working by doh on Sat, 2024-04-06 20:50 |
by doh Sat, 2024-04-06 20:50 |
VESC6 Beta | ||
|
VESC with Python on a RPi 5 by XAQ on Mon, 2025-09-15 01:06 |
by XAQ Mon, 2025-09-15 01:06 |
General discussion | ||
|
GSESC - Schematic review for new Hardware by CTSchorsch on Wed, 2020-01-29 15:41 |
by CTSchorsch Wed, 2020-01-29 15:41 |
Third Party Hardware | ||
|
vesc dual 6.6 plus problem firmware by Szergej on Mon, 2020-08-24 21:32 |
by Szergej Mon, 2020-08-24 21:32 |
VESC Firmware | ||
|
. by faheemift on Tue, 2021-03-30 15:37 |
by faheemift Thu, 2021-04-01 13:58 |
General discussion | ||
|
LoRa Support by CTSchorsch on Fri, 2021-12-17 13:59 |
by CTSchorsch Fri, 2021-12-17 13:59 |
Third Party Hardware | ||
|
Different rpm when using 3 vesc with can-bus by ewakegermanyhq on Wed, 2022-08-03 17:03 |
by ewakegermanyhq Wed, 2022-08-03 17:03 |
VESC Tool | ||
|
(Watchdog) - Resets with multipole engine. by edilger on Mon, 2023-06-26 12:33 |
by edilger Mon, 2023-06-26 12:33 |
VESC Firmware | ||
|
Dronecan 1036.StatusExtended message for motor temp by cjmssmd on Wed, 2024-09-04 02:05 |
by cjmssmd Wed, 2024-09-04 02:05 |
Feature Requests | ||
|
VESC to test e-Bike motor and car alternator as Torque Load..? by arifbustani on Thu, 2019-09-12 19:00 |
by arifbustani Thu, 2019-09-12 19:00 |
General discussion | ||
|
Motors wont turn independently by huffauden19 on Mon, 2020-11-30 06:24 |
by huffauden19 Mon, 2020-11-30 06:24 |
VESC Tool | ||
|
VESC appears to loose sync when increasing throttle by srinath on Sun, 2023-06-04 04:11 |
by srinath Sun, 2023-06-04 04:11 |
General discussion | ||
|
vesc hardware 4.12 by BasilBrushy on Fri, 2020-04-24 11:56 |
by BasilBrushy Fri, 2020-04-24 11:56 |
Third Party Hardware | ||
|
Startup codes? by anthonys on Sat, 2021-06-19 17:29 |
by anthonys Sat, 2021-06-19 17:29 |
VESC Tool | ||
|
Vesc firmware to programmable Sabvoton ml60 controller. by Maciejwarloch on Tue, 2022-03-08 14:19 |
by Maciejwarloch Tue, 2022-03-08 14:19 |
General discussion | ||
|
How to use an IMU and a PPM remote parallel by Gos1 on Tue, 2022-10-25 15:28 |
by Gos1 Wed, 2022-10-26 10:57 |
General discussion |
Pages
