You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
CAN STATUS INTERRUPTS MOTOR OUTPUT by v1n23nt on Tue, 2022-03-15 09:06 |
by v1n23nt Tue, 2022-03-15 09:10 |
General discussion | ||
|
VESC Tool Reporting RPM Different from Scope by bayetan on Wed, 2022-11-02 15:39 |
by bayetan Wed, 2022-11-02 15:39 |
VESC Firmware | ||
|
Issues with VESC 75/300 and VESC-Tool V3.01 by hpb66 on Fri, 2022-06-03 09:15 |
by hpb66 Fri, 2022-06-03 09:15 |
VESC Tool | ||
|
vesc tool v1.05 fw 3.51 by at_dts on Wed, 2020-09-23 20:12 |
by at_dts Wed, 2020-09-23 20:12 |
VESC Firmware | ||
|
HD60 CAN Resistor by BEWA on Wed, 2021-04-21 14:56 |
by BEWA Wed, 2021-04-21 14:56 |
VESC Original Hardware | ||
|
Problems driving motors in RPM mode by jediengineer on Fri, 2023-03-10 14:03 |
by jediengineer Fri, 2023-03-10 19:51 |
General discussion | ||
|
VESC cutout using smart reverse by Brokepilot on Thu, 2024-04-25 16:50 |
by Brokepilot Thu, 2024-04-25 16:50 |
General discussion | ||
|
PAS app: limit current depending on actual velocity by dpeinado on Fri, 2022-01-21 13:49 |
by dpeinado Fri, 2022-01-21 13:49 |
VESC Firmware | ||
|
Unstable current readings over VESC CAN (UART/USB are fine) by vukstijepovic on Mon, 2025-09-15 16:59 |
by vukstijepovic Mon, 2025-09-15 16:59 |
General discussion | ||
|
Defining when Watt-hour / Amp-hour Data are rezeroed by isabar on Sun, 2018-06-24 10:19 |
by isabar Sun, 2018-06-24 10:19 |
Feature Requests | ||
|
VESC 6 EDU: Motor Wizard - Detection failed by Navigator_PJE on Mon, 2022-08-29 16:12 |
by Navigator_PJE Mon, 2022-08-29 16:12 |
General discussion | ||
|
Roll to start by Oded Mazor on Sat, 2023-08-05 11:20 |
by Oded Mazor Sat, 2023-08-05 11:22 |
General discussion | ||
|
75/300 R2 FW higher than 3.62 ? it is possible? by Lasse on Sat, 2020-12-26 20:34 |
by Lasse Sat, 2020-12-26 20:34 |
VESC Firmware | ||
|
error message binding loop detected for property ! wtf by georg65 on Sat, 2024-09-28 08:49 |
by georg65 Tue, 2024-10-01 03:04 |
General discussion | ||
|
Install VESC on ubuntu 18.04 bionic by rest_vesc_001 on Tue, 2020-12-08 15:34 |
by rest_vesc_001 Tue, 2020-12-08 15:34 |
General discussion | ||
|
Adjusting Acceleration Ramp with NRF & Current control by Mido on Tue, 2022-04-05 14:36 |
by Mido Tue, 2022-04-05 14:36 |
General discussion | ||
|
Help needed please by Mark griffin on Tue, 2022-12-13 14:51 |
by Mark griffin Tue, 2022-12-13 14:51 |
General discussion | ||
|
How to order a VESC with native BLE ?? by Williamzoe2002 on Fri, 2024-12-13 09:31 |
by Williamzoe2002 Fri, 2024-12-13 09:31 |
General discussion | ||
|
LISP script to import data to MATLAB by cornballs on Thu, 2023-03-02 04:58 |
by cornballs Thu, 2023-03-02 06:07 |
General discussion | ||
|
VESC controller configuration for 350W hub motor, 48V motor. by lukepankratz on Mon, 2024-04-15 19:54 |
by lukepankratz Mon, 2024-04-15 19:54 |
General discussion |
Pages
