You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
Switch between pre-defined profiles over UART by PutridFox on Sun, 2025-06-15 13:11 |
by PutridFox Sun, 2025-06-15 13:11 |
General discussion | ||
|
Slowing down the speed when in low battery state by dsuresh on Tue, 2021-03-16 21:59 |
by dsuresh Tue, 2021-03-16 21:59 |
General discussion | ||
|
Throttle and Brake by shatty on Wed, 2021-03-10 01:19 |
by shatty Wed, 2021-03-10 01:22 |
VESC Tool | ||
|
Observer Gain? What is it and what does it affect? by kianK on Fri, 2023-05-26 10:53 |
by kianK Fri, 2023-05-26 10:53 |
VESC Firmware | ||
|
resistance and inductance value changes when each measurement by alexshen2012 on Fri, 2022-07-01 05:45 |
by alexshen2012 Fri, 2022-07-01 05:45 |
General discussion | ||
|
How to log events on a non bluetooth onewheel setup by carasta on Sat, 2023-05-13 22:01 |
by carasta Sat, 2023-05-13 22:01 |
VESC Tool | ||
|
How turn on /off Vesc MKS 75200 by baybradyr on Mon, 2024-07-01 22:10 |
by baybradyr Mon, 2024-07-01 22:10 |
General discussion | ||
|
Problem report: VESC keeps running at full reverse throttle after PPM input returns to mid-stick by chunkulator on Sun, 2019-08-11 00:34 |
by chunkulator Sun, 2019-08-11 00:34 |
VESC Firmware | ||
|
Where to find codelines for speed and position control structure by kianK on Tue, 2022-03-01 15:25 |
by kianK Thu, 2022-03-03 12:23 |
VESC Firmware | ||
|
Dultron X2 UP by timgunn5555 on Wed, 2026-03-18 02:34 |
by timgunn5555 Wed, 2026-03-18 02:34 |
General discussion | ||
|
how do you arm your Vesc in arduino code? by the creator on Wed, 2019-03-13 01:11 |
by the creator Wed, 2019-03-13 01:33 |
General discussion | ||
|
STM32F405RGTx LQFP64 .ioc file by gyongyoj on Fri, 2023-10-27 14:20 |
by gyongyoj Fri, 2023-10-27 14:20 |
VESC Tool | ||
|
PPM+UART. RC and esp32 by coldreboot on Thu, 2025-01-30 23:20 |
by coldreboot Fri, 2025-01-31 15:50 |
General discussion | ||
|
VESC Tool Makes my remote unusable by IcecreamSamurai on Mon, 2020-06-15 01:49 |
by IcecreamSamurai Mon, 2020-06-15 01:49 |
VESC Tool | ||
|
Vesc 6.5 - Issue with Canbus Status Command by Angelo99 on Thu, 2024-12-19 16:54 |
by Angelo99 Thu, 2024-12-19 16:54 |
VESC Firmware | ||
|
Cut-out at >40A by thewho on Thu, 2018-09-13 20:24 |
by thewho Thu, 2018-09-13 20:24 |
General discussion | ||
|
Wheelie control by fart on Wed, 2024-04-03 10:33 |
by fart Wed, 2024-04-03 10:33 |
Feature Requests | ||
|
VESC 4.12 Running Perfectly in sensorless mode but in Encoder Mode it is unable to run by Godfather on Sun, 2025-09-07 14:12 |
by Godfather Sun, 2025-09-07 14:12 |
VESC Original Hardware | ||
|
ADC Positive and Negative Ramping Time - not working by Astropower on Tue, 2019-05-28 22:41 |
by Astropower Tue, 2019-05-28 22:41 |
VESC Tool | ||
|
FOC Motor Detection Killed Motor? SOLVED by KirkusMaximus on Mon, 2020-08-31 02:20 |
by KirkusMaximus Tue, 2020-09-22 09:20 |
Third Party Hardware |
Pages
