You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
ADC INPUT with 4.10 HW running with 5.02 FW by mouadh on Tue, 2022-03-22 15:32 |
by mouadh Tue, 2022-03-22 17:38 |
General discussion | ||
|
Qt Creator Error - Solved by corgon on Sat, 2022-12-10 15:20 |
by corgon Sun, 2022-12-11 15:55 |
VESC Firmware | ||
|
ADC MAX Voltage 5volt ? by liteglow on Sat, 2020-07-25 23:48 |
by liteglow Sat, 2020-07-25 23:48 |
VESC Tool | ||
|
Vesc efficiency through log (.CSV) by th0masrtg on Tue, 2022-11-22 10:08 |
by th0masrtg Tue, 2022-11-22 10:08 |
VESC Tool | ||
|
How to set a jog speed using an encoder by AK6302019 on Wed, 2019-08-07 15:42 |
by AK6302019 Wed, 2019-08-07 15:42 |
General discussion | ||
|
VESC ramping problem by andrii619 on Mon, 2020-03-23 21:45 |
by andrii619 Mon, 2020-03-23 21:45 |
VESC Firmware | ||
|
VESC 4.12 wont connect to pc by stefann on Sun, 2020-03-15 00:42 |
by stefann Sun, 2020-03-15 00:42 |
VESC Original Hardware | ||
|
Minimum speed push cart using arduino by BarBumble on Wed, 2021-05-12 09:29 |
by BarBumble Wed, 2021-05-12 09:29 |
General discussion | ||
|
Current sensor and commanded current by galp on Fri, 2019-02-22 23:08 |
by galp Fri, 2019-02-22 23:08 |
General discussion | ||
|
VESC Setup - Fluctuating/Unstable Duty Cycle/eRPM/Current by liminalsunset on Thu, 2022-08-04 01:44 |
by liminalsunset Thu, 2022-08-04 01:44 |
General discussion | ||
|
Can't find good parameters for FOC detection by Kabroc on Thu, 2020-04-30 16:28 |
by Kabroc Thu, 2020-04-30 16:28 |
VESC Tool | ||
|
Switchign frequency issue? by Maxid on Thu, 2020-12-03 11:47 |
by Maxid Thu, 2020-12-03 11:47 |
VESC Firmware | ||
|
Flipsky 75100 rebooting under load by SpacePT on Tue, 2022-07-26 14:47 |
by SpacePT Tue, 2022-07-26 14:52 |
Third Party Hardware | ||
|
UART Safety Feature by jaghori.sasan on Wed, 2019-09-04 18:45 |
by jaghori.sasan Wed, 2019-09-04 18:45 |
VESC Tool | ||
|
*newbie* motors keep running backwards randomly when switch off, and then back on. Embarrassing. by Nikolas Lamshed on Sun, 2021-06-20 13:36 |
by Nikolas Lamshed Sun, 2021-06-20 13:36 |
General discussion | ||
|
Connecting handlebar controlls by mannberg on Thu, 2022-03-10 14:57 |
by mannberg Thu, 2022-03-10 14:57 |
General discussion | ||
|
HFI Tuning - "Start Voltage" Question by drummerboy5408 on Sat, 2022-11-12 03:12 |
by drummerboy5408 Sat, 2022-11-12 03:12 |
General discussion | ||
|
Calculator by kstuck on Tue, 2019-12-10 18:30 |
by kstuck Tue, 2019-12-10 18:30 |
General discussion | ||
|
connecting vesc tool with Prototipo by Govert on Thu, 2020-07-02 19:43 |
by Govert Thu, 2020-07-02 19:43 |
General discussion | ||
|
vesc 100250 Off-the-shelf motor by cuaxr on Mon, 2021-10-25 11:59 |
by cuaxr Mon, 2021-10-25 11:59 |
General discussion |
Pages
