You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
FSESC 4.2 motor power limited in sensored mode by motion_sickness on Mon, 2023-01-30 01:47 |
by motion_sickness Thu, 2023-02-02 18:25 |
Third Party Hardware | ||
|
servo input by Roger Wolff on Tue, 2018-07-03 07:50 |
by Roger Wolff Tue, 2018-07-03 07:50 |
VESC Firmware | ||
|
Motor command in log? by carboninfusion on Tue, 2020-08-04 07:58 |
by carboninfusion Tue, 2020-08-04 07:59 |
VESC Tool | ||
|
Need help maximizing torque at low RPM - FOC, Hub motors, Flipsky VESC 4.12 50A by Bruce on Mon, 2021-03-15 03:31 |
by Bruce Mon, 2021-03-15 03:31 |
General discussion | ||
|
Problem with encoder readings with arduino by ruthvikchanda on Thu, 2018-12-06 07:06 |
by ruthvikchanda Thu, 2018-12-06 10:23 |
General discussion | ||
|
The rpm control is not working properly by ptss37 on Wed, 2021-11-24 03:30 |
by ptss37 Wed, 2021-11-24 03:44 |
General discussion | ||
|
connect android to controller? by craigoroszi on Mon, 2025-05-19 20:53 |
by craigoroszi Mon, 2025-05-19 20:53 |
VESC Tool | ||
|
How to control a vesc controller without pulling electric wires on a bike? by peignier jacques on Sat, 2020-04-11 09:20 |
by peignier jacques Sat, 2020-04-11 09:21 |
Feature Requests | ||
|
What is the current state of mcus support? by il_piccione on Fri, 2025-04-25 09:47 |
by il_piccione Fri, 2025-04-25 09:47 |
General discussion | ||
|
Dollar signs break private messages by TechAUmNu on Tue, 2018-04-24 18:09 |
by TechAUmNu Tue, 2018-04-24 18:09 |
General discussion | ||
|
Integration of VESC with a display using I2C by dsuresh on Thu, 2021-05-20 19:32 |
by dsuresh Thu, 2021-05-20 19:32 |
General discussion | ||
|
PPM Pulselength mapping by Shaftdriver on Tue, 2022-10-04 17:18 |
by Shaftdriver Tue, 2022-10-04 17:18 |
VESC Tool | ||
|
weird ADC problem that only appears with 48V battery by kylerlaird on Sun, 2021-01-31 12:02 |
by kylerlaird Sun, 2021-01-31 12:02 |
VESC Original Hardware | ||
|
esc burning my motor by renaudbarbier on Tue, 2023-02-28 09:38 |
by renaudbarbier Tue, 2023-02-28 17:18 |
General discussion | ||
|
Need Help Setting Up Dual VESC on Trampa by MIKEtheBIKE on Wed, 2020-09-09 03:15 |
by MIKEtheBIKE Wed, 2020-09-09 03:15 |
VESC Tool | ||
|
AVERAGE ERPM (Max) Setting for dual vescs by Paul15578 on Fri, 2018-01-12 03:04 |
by Paul15578 Fri, 2018-01-12 03:04 |
Feature Requests | ||
|
12v(3s) Input to VESC 75/250 by AliBarrett10 on Wed, 2021-03-24 14:36 |
by AliBarrett10 Wed, 2021-03-24 16:19 |
General discussion | ||
|
Tenka esc in need of a reliable vesc tool by Vincent Gervais on Tue, 2021-12-21 00:48 |
by Vincent Gervais Tue, 2021-12-21 00:48 |
Third Party Hardware | ||
|
Tips on tuning PID for a 170mm RW170 hub motor, 15 pole-pairs, low speed, high torque, 0-3000 ERPM by PaulMakesThings on Fri, 2022-08-05 11:06 |
by PaulMakesThings Fri, 2022-08-05 11:06 |
General discussion | ||
|
Steering channel (dual vesc setup via CAN bus) by fender90 on Sun, 2020-04-26 03:47 |
by fender90 Sun, 2020-04-26 03:47 |
Feature Requests |
Pages
