You are here
Active forum topics
Primary tabs
Topic | Replies | Last post | Forum | |
---|---|---|---|---|
Need help maximizing torque at low RPM - FOC, Hub motors, Flipsky VESC 4.12 50A by Bruce on Mon, 2021-03-15 03:31 |
by Bruce Mon, 2021-03-15 03:31 |
General discussion | ||
Clicking File Location settings reset input configuration. Bug? by tiztrain on Mon, 2022-07-25 03:34 |
by tiztrain Mon, 2022-07-25 03:34 |
VESC Tool | ||
Problem with encoder readings with arduino by ruthvikchanda on Thu, 2018-12-06 07:06 |
by ruthvikchanda Thu, 2018-12-06 10:23 |
General discussion | ||
The rpm control is not working properly by ptss37 on Wed, 2021-11-24 03:30 |
by ptss37 Wed, 2021-11-24 03:44 |
General discussion | ||
How to control a vesc controller without pulling electric wires on a bike? by peignier jacques on Sat, 2020-04-11 09:20 |
by peignier jacques Sat, 2020-04-11 09:21 |
Feature Requests | ||
Dollar signs break private messages by TechAUmNu on Tue, 2018-04-24 18:09 |
by TechAUmNu Tue, 2018-04-24 18:09 |
General discussion | ||
Integration of VESC with a display using I2C by dsuresh on Thu, 2021-05-20 19:32 |
by dsuresh Thu, 2021-05-20 19:32 |
General discussion | ||
PPM Pulselength mapping by Shaftdriver on Tue, 2022-10-04 17:18 |
by Shaftdriver Tue, 2022-10-04 17:18 |
VESC Tool | ||
weird ADC problem that only appears with 48V battery by kylerlaird on Sun, 2021-01-31 12:02 |
by kylerlaird Sun, 2021-01-31 12:02 |
VESC Original Hardware | ||
esc burning my motor by renaudbarbier on Tue, 2023-02-28 09:38 |
by renaudbarbier Tue, 2023-02-28 17:18 |
General discussion | ||
Not too much features, and clean, tidy software. by ThierryGTLTS on Fri, 2017-09-08 13:10 |
by ThierryGTLTS Fri, 2017-09-08 13:10 |
Feature Requests | ||
Need Help Setting Up Dual VESC on Trampa by MIKEtheBIKE on Wed, 2020-09-09 03:15 |
by MIKEtheBIKE Wed, 2020-09-09 03:15 |
VESC Tool | ||
Hi by elsie on Thu, 2018-01-25 02:49 |
by elsie Thu, 2018-01-25 16:23 |
General discussion | ||
12v(3s) Input to VESC 75/250 by AliBarrett10 on Wed, 2021-03-24 14:36 |
by AliBarrett10 Wed, 2021-03-24 16:19 |
General discussion | ||
Tenka esc in need of a reliable vesc tool by Vincent Gervais on Tue, 2021-12-21 00:48 |
by Vincent Gervais Tue, 2021-12-21 00:48 |
Third Party Hardware | ||
Tips on tuning PID for a 170mm RW170 hub motor, 15 pole-pairs, low speed, high torque, 0-3000 ERPM by PaulMakesThings on Fri, 2022-08-05 11:06 |
by PaulMakesThings Fri, 2022-08-05 11:06 |
General discussion | ||
Steering channel (dual vesc setup via CAN bus) by fender90 on Sun, 2020-04-26 03:47 |
by fender90 Sun, 2020-04-26 03:47 |
Feature Requests | ||
controller_id on COMM_GET_IMU_DATA by andrea.scipione on Sun, 2020-11-22 19:07 |
by andrea.scipione Sun, 2020-11-22 19:07 |
Feature Requests | ||
Ground Loop question by a.smith on Wed, 2021-06-23 13:25 |
by a.smith Wed, 2021-06-23 13:25 |
General discussion | ||
Need IRF7759 by marcel7162 on Fri, 2022-03-18 22:29 |
by marcel7162 Fri, 2022-03-18 22:29 |
Third Party Hardware |