You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
Can't get motor to run using COMM port on vesc 6 MKVI and arduino mega with a potentiometer and SolidGeeks UART library by Kokonenen on Thu, 2023-03-30 11:41 |
1 |
by Kokonenen Thu, 2023-03-30 16:19 |
General discussion | |
|
how I can connect 4 vesc using CAN and how connect vesc to PC via CAN bus? by Chanyoung Jung on Mon, 2020-03-09 08:12 |
1 |
by hexakopter Sat, 2020-04-18 13:12 |
General discussion | |
|
ADC TMM Sensor Voltage fluctuation by gianni on Sun, 2019-06-23 16:09 |
1 |
by gianni Mon, 2019-09-23 14:52 |
General discussion | |
|
Understanding VESC Hardware and $40 VESC target by ripperpc on Thu, 2020-02-27 06:41 |
1 |
by vadicus Mon, 2020-03-23 20:18 |
Third Party Hardware | |
|
Help Setup Flipsky FSESC 4.12 by R66 on Mon, 2025-09-29 05:23 |
1 |
by R66 Mon, 2025-09-29 06:58 |
General discussion | |
|
Brake rpm minimum by mcspikesky on Sat, 2023-07-22 22:51 |
1 |
by mcspikesky Tue, 2023-07-25 22:03 |
General discussion | |
|
Esc does not reply by nemethLali on Sun, 2021-08-01 16:07 |
1 |
by nemethLali Fri, 2021-08-06 22:18 |
Third Party Hardware | |
|
Cant find firmware by Rad07 on Sun, 2024-09-15 01:05 |
1 |
by Sharkboy Sat, 2024-09-21 23:47 |
VESC Firmware | |
|
Motor stuttering at lower duty cycle % by trueskyaiways on Thu, 2024-06-20 05:42 |
1 |
by vadicus Fri, 2024-06-21 06:18 |
General discussion | |
|
Flipsky FSESC75450 ABI encoder setup by CheatingBoy6890 on Fri, 2026-03-20 20:23 |
1 |
by CheatingBoy6890 Fri, 2026-03-27 20:02 |
Third Party Hardware | |
|
FOC configuration - Motor stalls during measurement by Lukinio on Wed, 2021-05-26 12:31 |
1 |
by Lukinio Wed, 2021-05-26 12:44 |
VESC Tool | |
|
Difference between ERPM and Duty Cycle by dormanae on Wed, 2022-02-23 17:21 |
1 |
by j.konrad Thu, 2022-02-24 02:08 |
General discussion | |
|
Dual motor fishing boat by Snabelost on Mon, 2022-10-17 02:41 |
1 |
by canoeman Tue, 2022-10-25 15:11 |
Projects incorporating VESC technology | |
|
Input Setup Wizard Does Not Ask if Single or Multi VESC by kylemuramatsu on Wed, 2019-03-13 03:22 |
1 |
by benjamin Wed, 2019-03-13 09:38 |
General discussion | |
|
75/300 Large inrunner problem (video) by dk-odense on Mon, 2019-11-04 21:53 |
1 |
by frank Tue, 2019-11-05 09:06 |
General discussion | |
|
VESC Mini 4.20 boots up inconsistently, any suggestions by Djmrozinski on Sat, 2021-02-06 10:54 |
1 |
by skyline1970 Sat, 2021-02-06 19:08 |
General discussion | |
|
Stream realtime data stops streaming by b.visser@studen... on Fri, 2018-09-14 16:09 |
1 |
by thewho Thu, 2018-12-13 21:27 |
Third Party Hardware | |
|
How to read VESC fault / status over CAN? by reobaird on Tue, 2023-03-07 00:06 |
1 |
by frank Tue, 2023-03-07 10:49 |
General discussion | |
|
auxiliary output mode? by shaman on Thu, 2020-02-20 01:23 |
1 |
by skyline1970 Mon, 2021-02-01 21:07 |
VESC Tool | |
|
Use sensors on the output shaft of a motor attached to a large gear ratio gearbox by davidq1688 on Wed, 2022-04-27 05:23 |
1 |
by tobiokanobi Thu, 2022-04-28 14:48 |
VESC Tool |
Pages
