You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
Lawn mower by charper on Mon, 2018-12-03 14:25 |
by charper Mon, 2018-12-03 14:25 |
General discussion | ||
|
[solved] Firmware 5.01 gcc compile fail.. need some insight by Bill Somerville on Tue, 2020-11-03 19:44 |
by Bill Somerville Fri, 2020-11-06 23:20 |
VESC Firmware | ||
|
Terminal Command for Current? by Mannerow on Thu, 2020-10-29 23:07 |
by Mannerow Thu, 2020-10-29 23:07 |
VESC Tool | ||
|
Direct drive wheel ac servo+vesc by adilrepas on Wed, 2021-05-26 12:50 |
by adilrepas Wed, 2021-05-26 12:58 |
General discussion | ||
|
Request Feature to add minimum Battery Voltage value in addition to duty cycle for field weakening by aquaponiccowboy on Mon, 2022-10-17 04:49 |
by aquaponiccowboy Mon, 2022-10-17 04:50 |
Feature Requests | ||
|
how to communication with arduino on vesc via CAN by yuri12 on Tue, 2022-02-08 13:16 |
by yuri12 Tue, 2022-02-08 13:16 |
VESC Tool | ||
|
VESC Tool for Android & GPS/GNSS sharing? by ahagge on Fri, 2021-10-01 05:04 |
by ahagge Fri, 2021-10-01 05:04 |
VESC Tool | ||
|
Programmable freewheel function by baumeister on Wed, 2023-10-11 09:16 |
by baumeister Thu, 2023-10-12 11:08 |
VESC Tool | ||
|
Encoder support in BLDC by dirkvl on Sat, 2021-09-18 12:21 |
by dirkvl Sat, 2021-09-18 12:21 |
Feature Requests | ||
|
CAN sends error frame by dgarciasoto on Wed, 2022-04-27 07:11 |
by dgarciasoto Wed, 2022-04-27 07:11 |
VESC Firmware | ||
|
FOC settings are working in one VESC hardware and not in another VESC hardware with same hardware version ( VESC 6MKVI ) by Pranit Bhamare on Fri, 2023-02-17 07:17 |
by Pranit Bhamare Fri, 2023-02-17 07:17 |
General discussion | ||
|
2kW motor with VESS 75200 by Sazabi on Fri, 2024-04-05 11:17 |
by Sazabi Fri, 2024-04-05 11:18 |
General discussion | ||
|
FAULT CODE UNBALANCED CURRENT by NOAI on Mon, 2024-03-25 09:30 |
by NOAI Mon, 2024-03-25 09:30 |
Third Party Hardware | ||
|
Auxiliary Output Mode pin# by garyp on Sat, 2020-08-22 18:17 |
by garyp Sat, 2020-08-22 18:17 |
General discussion | ||
|
Cruise function already implemented? by sam.vanratt on Wed, 2019-01-02 17:05 |
by sam.vanratt Wed, 2019-01-02 17:20 |
General discussion | ||
|
Problems getting Cruise control to run properly with the new wand - dual VESC6 by MaddiQ on Mon, 2019-09-16 19:36 |
by MaddiQ Mon, 2019-09-16 19:36 |
VESC Firmware | ||
|
(CLOSED)Custom FW based on beta "could not deserialize" by pe on Wed, 2021-12-15 11:48 |
by pe Wed, 2021-12-15 15:18 |
VESC Development and Beta Testing | ||
|
Sensorless FOC with Duty Cycle will not stop spinning by moose09876 on Mon, 2022-08-01 18:08 |
by moose09876 Mon, 2022-08-01 18:08 |
General discussion | ||
|
-solved- by KittenDude on Sat, 2020-11-28 06:30 |
by KittenDude Sun, 2020-11-29 19:27 |
General discussion | ||
|
Issue with Vesc Tool: MPU6050 IMU Not Detected After Power Cycling by Lennart Duijn on Thu, 2023-06-01 21:54 |
by Lennart Duijn Fri, 2023-06-02 09:03 |
VESC Tool |
Pages
