You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
VESC with Raspberry Pi 3 by Antonio Rodrígu... on Sun, 2018-06-03 18:54 |
9 |
by ShortCircuit Thu, 2018-06-28 15:33 |
General discussion | |
|
Invert motor direction. by Sanjoy on Thu, 2017-06-15 23:31 |
9 |
by Roger Wolff Mon, 2017-06-19 16:00 |
VESC6 Beta | |
|
FAULT_CODE_ABS_OVER_CURRENT on custom pcb by TVAVAE on Sat, 2021-07-10 00:44 |
9 |
by hakan seray Wed, 2022-06-15 12:27 |
Third Party Hardware | |
|
VESC Tool Compatible With FW 3.34 by a.ceviker on Sun, 2018-07-29 11:38 |
9 |
by bitmixer Fri, 2020-02-21 22:18 |
VESC Tool | |
|
IGBT Vesc FOC not working by ziumus on Sat, 2019-09-28 15:48 |
9 |
by bgdwiepp Sat, 2019-10-19 21:56 |
Third Party Hardware | |
|
Dead VESC6 due to shot from UBEC, repair possible? by Boesila on Sat, 2018-04-14 11:35 |
9 |
by benjamin Tue, 2018-06-26 14:37 |
VESC6 Beta | |
|
Firmware for 4.xx VESC in new VESC Tool? by sl33py on Wed, 2017-06-28 21:27 |
9 |
by sl33py Fri, 2017-07-14 08:29 |
VESC6 Beta | |
|
Problem with burned FETs and drivers after reconnect battery by CTSchorsch on Sat, 2021-01-16 19:49 |
9 |
by CTSchorsch Wed, 2021-02-17 13:42 |
Third Party Hardware | |
|
Forward/brake/reverse mode? by RDN2003 on Thu, 2019-10-03 02:13 |
9 |
by Toymanfrank Sun, 2026-04-26 03:49 |
General discussion | |
|
Braking in speed PID controlled mode by vadimz on Sat, 2018-09-15 14:19 |
9 |
by zybyxutese Mon, 2019-04-01 13:35 |
General discussion | |
|
Low power VESC - any available by wdaehn on Wed, 2018-02-28 18:02 |
9 |
by TechAUmNu Mon, 2018-03-19 11:54 |
Third Party Hardware | |
|
Problem with Bluetooth connection (HM-10) by squdowx on Mon, 2018-07-30 15:56 |
9 |
by CTSchorsch Thu, 2019-12-05 21:27 |
General discussion | |
|
Noise with Hall sensor at high speed by yosoufe on Thu, 2018-03-08 12:34 |
9 |
by yosoufe Tue, 2018-03-20 09:30 |
General discussion | |
|
ERPM settings restrict carving speed on outer wheel. Poor user experience. by Paul15578 on Fri, 2018-01-12 02:28 |
9 |
by Ackmaniac Tue, 2018-04-24 13:47 |
General discussion | |
|
FAULT_CODE_UNDER_VOLTAGE by alexantosh on Mon, 2021-11-29 09:26 |
9 |
by heravinluca Thu, 2022-08-04 04:19 |
VESC Tool | |
|
Problems with Initial flash of Hw4:12 by Idoff on Mon, 2018-04-16 18:47 |
9 |
by Frankfartin2077 Thu, 2019-04-04 10:10 |
VESC Firmware | |
|
Serial Connection Lost with Vesc6.6 Firmware 5.2 and Vesc Tool 3.0 by Dan Slanker on Wed, 2021-04-28 16:56 |
9 |
by AngelKillR Wed, 2022-09-28 05:10 |
General discussion | |
|
vesc tool 1.25 not opening. by osis on Tue, 2019-10-29 20:50 |
9 |
by flyingbrike Wed, 2021-09-08 09:06 |
VESC Tool | |
|
VESC Tool on Mac keeps crashing on Bluetooth connect by ala.ric_ on Thu, 2023-02-16 21:45 |
9 |
by etavav Fri, 2025-09-19 15:24 |
VESC Tool | |
|
Failure in Motor Set Up by Toshi Sharma on Tue, 2022-01-11 15:19 |
9 |
by frank Thu, 2022-01-13 14:15 |
General discussion |
Pages
