You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
Is there a VESC with the form factor like a Votol EM200 ? (with those threaded lugs|Screw Terminals)) by Gatze on Sat, 2022-03-12 09:33 |
8 |
by qdxiatao Sat, 2022-08-20 04:09 |
General discussion | |
|
Flipsky HC 200A VESC programming to eFoil motor by tylerclark on Wed, 2020-03-11 05:52 |
8 |
by okarbon Tue, 2021-02-23 13:19 |
VESC Firmware | |
|
Why is the speed lower in FOC mode than BLDC mode ? by stone_1706 on Thu, 2019-01-17 08:23 |
8 |
by speed3r Wed, 2022-06-15 09:34 |
General discussion | |
|
No UART Output on VESC6 MKIV by uwala on Sun, 2020-10-25 12:13 |
8 |
by tsm Tue, 2021-12-21 15:20 |
VESC Development and Beta Testing | |
|
Detection failed. Reason: Sensor detection failed by Lilian_CASTEL on Tue, 2020-11-24 11:31 |
8 |
by electricfox Thu, 2023-02-16 15:57 |
VESC Tool | |
|
Communication with Vesc Tools by faheemift on Tue, 2021-02-09 16:08 |
8 |
by beatrixena Sat, 2021-02-20 09:11 |
General discussion | |
|
How to fix VESC killed by over current in serial comm? by 8bit on Sun, 2021-05-16 04:02 |
8 |
by vadicus Fri, 2023-01-13 19:15 |
Third Party Hardware | |
|
VESC 75/300 and EMC Tests for motorcycle conversion by gotfatalErrs on Tue, 2020-06-02 18:34 |
8 |
by Bubu54 Wed, 2024-09-04 13:52 |
General discussion | |
|
Problems with Initial flash of Hw4:12 by Idoff on Mon, 2018-04-16 18:47 |
9 |
by Frankfartin2077 Thu, 2019-04-04 10:10 |
VESC Firmware | |
|
ERPM settings restrict carving speed on outer wheel. Poor user experience. by Paul15578 on Fri, 2018-01-12 02:28 |
9 |
by Ackmaniac Tue, 2018-04-24 13:47 |
General discussion | |
|
Rough acceleration - BLDC & FOC by Loose Nickers on Tue, 2020-02-11 07:56 |
9 |
by MC_DIY_Beginner Mon, 2022-05-16 13:34 |
VESC Tool | |
|
VESC recommendation for sailboat conversion by Henque19 on Thu, 2019-11-28 00:42 |
9 |
by Henque19 Fri, 2019-12-20 16:15 |
General discussion | |
|
FAULT_CODE_ABS_OVER_CURRENT on custom pcb by TVAVAE on Sat, 2021-07-10 00:44 |
9 |
by hakan seray Wed, 2022-06-15 12:27 |
Third Party Hardware | |
|
Flux linkage observer @ low speed by soltesz on Sun, 2017-12-17 16:33 |
9 |
by benjamin Thu, 2017-12-21 10:17 |
VESC Firmware | |
|
IGBT Vesc FOC not working by ziumus on Sat, 2019-09-28 15:48 |
9 |
by bgdwiepp Sat, 2019-10-19 21:56 |
Third Party Hardware | |
|
Problem with burned FETs and drivers after reconnect battery by CTSchorsch on Sat, 2021-01-16 19:49 |
9 |
by CTSchorsch Wed, 2021-02-17 13:42 |
Third Party Hardware | |
|
15S support (and more amps) by Torxed on Mon, 2018-07-16 12:06 |
9 |
by Torxed Sat, 2018-07-21 21:52 |
Feature Requests | |
|
Acceleration control to desired RPM by bjohns on Fri, 2018-07-20 22:08 |
9 |
by arvidb Thu, 2018-08-09 21:15 |
General discussion | |
|
Serial Connection Lost with Vesc6.6 Firmware 5.2 and Vesc Tool 3.0 by Dan Slanker on Wed, 2021-04-28 16:56 |
9 |
by AngelKillR Wed, 2022-09-28 05:10 |
General discussion | |
|
FAULT_CODE_UNDER_VOLTAGE by alexantosh on Mon, 2021-11-29 09:26 |
9 |
by heravinluca Thu, 2022-08-04 04:19 |
VESC Tool |
Pages
