You are here
Active forum topics
Primary tabs
Topic | Replies | Last post | Forum | |
---|---|---|---|---|
Motors spin up during detection but then won't move by jordan314 on Thu, 2019-02-21 09:18 |
12 |
by KDoc Tue, 2023-01-17 00:13 |
VESC Tool | |
FlipSky 75/300 + Alien 80 KV noise/vibration under load by brendangillatt on Thu, 2021-01-07 01:19 |
12 |
by vadicus Fri, 2021-01-22 18:14 |
General discussion | |
Hoverboard Motor with VESC by mados73 on Wed, 2018-03-21 22:14 |
12 |
by Kirkness Mon, 2020-07-13 01:00 |
General discussion | |
temp motor by emmaanuel on Wed, 2017-09-13 01:27 |
12 |
by Roger Wolff Wed, 2017-11-08 16:23 |
VESC Firmware | |
Uploaded the wrong firmware, now I need help to debug :P by Frazatto on Tue, 2018-08-21 15:46 |
12 |
by Frazatto Tue, 2018-09-04 19:33 |
Third Party Hardware | |
FOC with encoder by Ledz on Tue, 2018-05-15 11:55 |
12 |
by Ramesh Thu, 2023-12-21 07:22 |
General discussion | |
Gan Fets by transcendStaticMode on Tue, 2020-05-05 05:52 |
12 |
by lizardmech Tue, 2023-11-14 13:35 |
Feature Requests | |
VESC 75/300 Overheating issues by tecnico.solarboat on Sat, 2020-10-17 00:52 |
12 |
by Gerhard Tue, 2020-12-22 13:19 |
VESC Original Hardware | |
Realtime time axis by Eric on Tue, 2017-09-05 14:29 |
12 |
by hexakopter Mon, 2017-10-23 20:23 |
VESC Tool | |
Experience with QS120 IPM motor? by marvinrau on Mon, 2021-05-31 14:03 |
12 |
by pe Tue, 2021-11-16 18:20 |
General discussion | |
ADC pin voltage not zero by zoppp on Fri, 2019-02-08 23:44 |
12 |
by zoppp Tue, 2019-03-12 01:17 |
General discussion | |
FSESC 6.6 not Connecting to VESC Tool by billyredwood01 on Sat, 2020-11-28 12:34 |
12 |
by JP Mon, 2023-04-03 13:02 |
General discussion | |
Trying to connect over USB, but new 6.4 connects and disconnects a few seconds later. by MaxMaker1 on Thu, 2018-05-24 16:15 |
12 |
by frank Thu, 2019-02-21 20:34 |
VESC Tool | |
Adjusting Beta Value for Motor Thermistor. by Ecyclist on Thu, 2018-12-06 23:22 |
12 |
by Ecyclist Tue, 2019-01-29 04:29 |
VESC Tool | |
VESC-Tool Bugs by Danny Bokma on Sun, 2017-06-04 01:44 |
13 |
by sevenfloorsdown Wed, 2022-03-23 22:45 |
VESC6 Beta | |
VESC 75/300 Configuration problems with Hacker Q80 Motors by electricfox on Thu, 2019-02-28 18:23 |
13 |
by Cherry Tue, 2021-01-12 11:56 |
VESC Tool | |
Driving 2 BLDC motors with one MCU by Pimousse on Tue, 2018-06-26 15:42 |
13 |
by wkt Wed, 2018-10-17 14:02 |
Third Party Hardware | |
Can't connect to slave vesc via master usb in vesc-tool -SOLVED- by rich on Mon, 2017-07-24 13:31 |
13 |
by fadez Tue, 2019-09-17 14:11 |
VESC6 Beta | |
F50-300 (Design Not Tested yet) by mrendu43 on Tue, 2021-03-09 11:49 |
13 |
by mrendu43 Sat, 2021-05-01 17:15 |
Third Party Hardware | |
VESC Trampa 6 75V firmware by kistvan97 on Wed, 2022-10-05 12:51 |
13 |
by cole.023 Tue, 2023-02-14 17:56 |
VESC Firmware |