You are here
Active forum topics
Primary tabs
Topic | Replies | Last post | Forum | |
---|---|---|---|---|
Custom Apps by HammerHeadFett on Fri, 2020-07-17 00:10 |
9 |
by CTSchorsch Wed, 2021-12-22 09:12 |
VESC Tool | |
ERPM to Rpm by faheemift on Wed, 2021-03-31 11:11 |
9 |
by faheemift Wed, 2021-04-14 13:01 |
General discussion | |
Noise with Hall sensor at high speed by yosoufe on Thu, 2018-03-08 12:34 |
9 |
by yosoufe Tue, 2018-03-20 09:30 |
General discussion | |
Importance of the MK version and Determining the MK version of the VESC by alexantosh on Tue, 2021-11-23 12:15 |
9 |
by alexantosh Tue, 2021-11-30 13:58 |
VESC Firmware | |
Problems with Initial flash of Hw4:12 by Idoff on Mon, 2018-04-16 18:47 |
9 |
by Frankfartin2077 Thu, 2019-04-04 10:10 |
VESC Firmware | |
ERPM settings restrict carving speed on outer wheel. Poor user experience. by Paul15578 on Fri, 2018-01-12 02:28 |
9 |
by Ackmaniac Tue, 2018-04-24 13:47 |
General discussion | |
Rough acceleration - BLDC & FOC by Loose Nickers on Tue, 2020-02-11 07:56 |
9 |
by MC_DIY_Beginner Mon, 2022-05-16 13:34 |
VESC Tool | |
VESC recommendation for sailboat conversion by Henque19 on Thu, 2019-11-28 00:42 |
9 |
by Henque19 Fri, 2019-12-20 16:15 |
General discussion | |
FAULT_CODE_ABS_OVER_CURRENT on custom pcb by TVAVAE on Sat, 2021-07-10 00:44 |
9 |
by hakan seray Wed, 2022-06-15 12:27 |
Third Party Hardware | |
Flux linkage observer @ low speed by soltesz on Sun, 2017-12-17 16:33 |
9 |
by benjamin Thu, 2017-12-21 10:17 |
VESC Firmware | |
IGBT Vesc FOC not working by ziumus on Sat, 2019-09-28 15:48 |
9 |
by bgdwiepp Sat, 2019-10-19 21:56 |
Third Party Hardware | |
VESC settings for large scooter motor by trimen on Tue, 2020-07-14 22:15 |
9 |
by pwn1j Tue, 2024-07-02 23:30 |
General discussion | |
Problem with burned FETs and drivers after reconnect battery by CTSchorsch on Sat, 2021-01-16 19:49 |
9 |
by CTSchorsch Wed, 2021-02-17 13:42 |
Third Party Hardware | |
15S support (and more amps) by Torxed on Mon, 2018-07-16 12:06 |
9 |
by Torxed Sat, 2018-07-21 21:52 |
Feature Requests | |
Acceleration control to desired RPM by bjohns on Fri, 2018-07-20 22:08 |
9 |
by arvidb Thu, 2018-08-09 21:15 |
General discussion | |
Help is there an issue with my new Vesc 6 by avis on Sat, 2017-09-30 15:21 |
9 |
by frank Wed, 2017-10-04 17:10 |
General discussion | |
Serial Connection Lost with Vesc6.6 Firmware 5.2 and Vesc Tool 3.0 by Dan Slanker on Wed, 2021-04-28 16:56 |
9 |
by AngelKillR Wed, 2022-09-28 05:10 |
General discussion | |
FAULT_CODE_UNDER_VOLTAGE by alexantosh on Mon, 2021-11-29 09:26 |
9 |
by heravinluca Thu, 2022-08-04 04:19 |
VESC Tool | |
vesc tool 1.25 not opening. by osis on Tue, 2019-10-29 20:50 |
9 |
by flyingbrike Wed, 2021-09-08 09:06 |
VESC Tool | |
Invert motor direction. by Sanjoy on Thu, 2017-06-15 23:31 |
9 |
by Roger Wolff Mon, 2017-06-19 16:00 |
VESC6 Beta |