You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
Smart Reverse Minimum Erpm by ZenRides on Wed, 2022-02-16 05:36 |
4 |
by nabil sassi Tue, 2022-04-12 23:21 |
VESC Tool | |
|
Kill switch feature through adc input by Heddan99 on Sun, 2021-03-07 12:54 |
4 |
by frank Thu, 2021-06-10 14:18 |
Feature Requests | |
|
Full Throttle direct after input deadband by toerde on Sat, 2022-04-30 18:54 |
4 |
by frank Mon, 2022-05-09 08:22 |
General discussion | |
|
Cannot reach max speed of BLDC motor by rousha42 on Wed, 2021-11-03 20:23 |
4 |
by frank Tue, 2021-11-09 09:46 |
General discussion | |
|
Feature request: Raw hall data. by Roger Wolff on Mon, 2018-06-11 15:49 |
4 |
by blubbi321 Tue, 2022-03-29 16:32 |
VESC Tool | |
|
Need Help with HI200-C from Maker X by Moritz@liebler.net on Tue, 2021-01-12 14:44 |
4 |
by Oded Mazor Thu, 2022-03-24 12:05 |
Third Party Hardware | |
|
BLDC vs FOC mode， motor‘s spin direction is invert by moto_guy on Wed, 2019-02-20 11:48 |
4 |
by moto_guy Sun, 2019-02-24 09:11 |
General discussion | |
|
Look at my amazing BLDC, see something weird? (help plz) by javivi on Thu, 2020-02-06 16:19 |
4 |
by roelth Sun, 2020-02-23 20:01 |
Third Party Hardware | |
|
Hall sensors signals tolerance by Pimousse on Tue, 2019-09-17 13:55 |
4 |
by e-biker Wed, 2019-10-09 12:40 |
General discussion | |
|
Can motor parameters be detected with shaft load? by powerlabor001 on Thu, 2018-03-15 13:24 |
4 |
by powerlabor001 Sat, 2018-03-24 03:07 |
General discussion | |
|
VESC for IOS by keanusam on Tue, 2022-01-18 14:35 |
4 |
by Cristof Wed, 2022-09-28 11:10 |
The VESC-Project | |
|
How to increase startup torque? by Enak on Fri, 2017-09-08 01:14 |
4 |
by vadicus Tue, 2021-02-23 19:44 |
VESC Tool | |
|
Delay on reverse function on electric boat by FreddyForLaunch on Tue, 2021-06-01 12:31 |
4 |
by electricfox Wed, 2022-08-17 20:59 |
VESC Tool | |
|
Change HW after wrong Firmware Update by Hassi on Sun, 2017-10-01 15:46 |
4 |
by benjamin Sun, 2017-10-22 23:32 |
VESC Tool | |
|
Ericson 41 with electric motor driven by FS 75200 by Svein Utne on Tue, 2023-03-07 09:12 |
4 |
by Svein Utne Sun, 2023-03-12 06:49 |
Projects incorporating VESC technology | |
|
Motor Types by ellen.scott on Fri, 2021-03-05 10:50 |
4 |
by ellen.scott Tue, 2021-03-23 12:45 |
General discussion | |
|
Can't receive status message via CAN bus by IanG on Mon, 2020-04-13 03:50 |
4 |
by olivierabristol Sun, 2022-02-27 08:31 |
General discussion | |
|
Bafang hub motor setup by Kent Tabor on Fri, 2020-10-16 03:48 |
4 |
by Racing2Learn Sun, 2024-05-05 18:31 |
VESC Tool | |
|
Increasing phase amps beyond 300a on 100-250 by reubarb.scons on Tue, 2022-03-15 07:30 |
4 |
by reubarb.scons Thu, 2022-03-17 22:28 |
VESC Original Hardware | |
|
Charge wires by Phill Dixon on Tue, 2017-10-24 14:24 |
4 |
by linsus Tue, 2017-11-21 14:39 |
General discussion |
Pages
