You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
Motor shaft machining advices are welcome! by ThierryGTLTS on Tue, 2017-11-14 17:40 |
5 |
by William Yates Mon, 2017-12-18 18:22 |
The VESC-Project | |
|
Flipsky VESC 50A by CraigL100 on Fri, 2019-08-30 16:57 |
5 |
by CraigL100 Sat, 2019-09-14 12:10 |
Third Party Hardware | |
|
VESC safety by alexantosh on Tue, 2021-11-23 15:47 |
5 |
by alexantosh Tue, 2021-12-28 15:10 |
General discussion | |
|
Logging additional Sensors with the VESC on the Phone App by palm369 on Sat, 2024-07-13 19:10 |
5 |
by palm369 Sun, 2024-11-10 13:13 |
General discussion | |
|
Dual motor control on VESC6 / 6.00.58 by jediengineer on Mon, 2022-10-10 19:21 |
5 |
by RSR Sat, 2025-08-09 18:23 |
VESC Firmware | |
|
Sine Wave Frequency by speed3r on Mon, 2019-03-04 14:11 |
5 |
by TheFallen Sun, 2019-03-10 18:06 |
VESC Firmware | |
|
Paypal alternative by sam.vanratt on Sat, 2019-01-05 22:03 |
5 |
by benjamin Mon, 2019-02-18 20:11 |
The VESC-Project | |
|
SK3 Turnigy 6374 149 / encoder CUI AMT102 => can VESC 4 support position control? by fourchette on Tue, 2019-04-02 23:14 |
5 |
by pf26 Thu, 2019-04-04 11:43 |
General discussion | |
|
Advice please - VESC6 controller for a specific model aircraft application by aabill on Wed, 2019-11-27 11:31 |
5 |
by frank Sun, 2019-12-01 17:28 |
General discussion | |
|
Sudden kick (from motor current cut off?) by darowi on Mon, 2017-10-02 18:56 |
5 |
by darowi Tue, 2020-09-15 12:45 |
General discussion | |
|
Dual brushed motors from 1 R/C stick? by VESC1 on Thu, 2019-01-31 06:19 |
5 |
by sam.vanratt Sun, 2019-02-03 16:30 |
General discussion | |
|
tips for power design by antonchromjak on Mon, 2021-04-12 18:34 |
5 |
by vadicus Tue, 2021-04-27 03:01 |
Third Party Hardware | |
|
Current In vs Current Motor by hacksmithCabe on Thu, 2021-09-30 21:59 |
5 |
by y-hasebe Mon, 2021-12-13 15:17 |
VESC Tool | |
|
Vesc Max current 90A Vs ESC Max current 135A? by ScootScoot on Tue, 2021-12-14 13:00 |
5 |
by Markula Thu, 2021-12-16 20:42 |
General discussion | |
|
Data logging for dual VESC on Android VESC-tool by elmardus on Wed, 2021-10-20 16:13 |
5 |
by SamuL Fri, 2023-02-17 00:55 |
VESC Tool | |
|
VESC & CAN Bus Communication to another MCU (NOT VESC) by Jack_Li on Thu, 2019-07-11 04:08 |
5 |
by David_1 Thu, 2022-08-11 22:08 |
VESC Firmware | |
|
Dual motor setup over CAN with UART by Pawel on Sun, 2018-06-17 11:50 |
5 |
by alex63610 Fri, 2019-12-27 14:27 |
VESC Firmware | |
|
Rough transition to sensorless under load by vadicus on Sat, 2020-07-18 07:10 |
5 |
by vadicus Wed, 2020-08-05 20:10 |
General discussion | |
|
step/dir by blueflower on Thu, 2020-01-16 04:15 |
5 |
by akkoxe Mon, 2022-08-08 06:34 |
General discussion | |
|
Motor control by ptss37 on Wed, 2021-12-08 06:52 |
5 |
by ptss37 Fri, 2021-12-10 03:24 |
VESC Tool |
Pages
