You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
Brushless or brushed motor for autonomous rc-car by Joe_Lowtech on Thu, 2018-12-20 11:56 |
4 |
by Joe_Lowtech Tue, 2019-03-05 11:00 |
General discussion | |
|
foc_openloop does not work. by Roger Wolff on Sun, 2017-06-18 14:10 |
4 |
by lizardmech Fri, 2017-06-23 18:32 |
VESC6 Beta | |
|
Hall sensors signals tolerance by Pimousse on Tue, 2019-09-17 13:55 |
4 |
by e-biker Wed, 2019-10-09 12:40 |
General discussion | |
|
Vesc is not working by Patryk on Mon, 2018-10-08 18:48 |
4 |
by Patryk Fri, 2018-10-19 22:25 |
General discussion | |
|
Trouble with custom hardware design by Evgeni on Sun, 2022-03-06 21:46 |
4 |
by Evgeni Tue, 2022-03-15 21:20 |
Third Party Hardware | |
|
dual vesc by badger1666 on Fri, 2018-09-21 09:10 |
4 |
by badger1666 Sat, 2018-09-29 15:45 |
General discussion | |
|
FSESC 4.2 problem at full speed .. by lurch on Fri, 2021-10-22 19:27 |
4 |
by lurch Mon, 2021-11-01 15:09 |
Third Party Hardware | |
|
Red flashing light? by givol on Thu, 2019-07-04 03:06 |
4 |
by wimleo Thu, 2024-01-18 09:53 |
Third Party Hardware | |
|
Are the FOC PID values for discrete or continuous time controllers? by ward on Fri, 2022-01-21 15:55 |
4 |
by Elwin Tue, 2022-01-25 07:48 |
VESC Original Hardware | |
|
Cannot get any PPM signals from Arduino. Or is it just the VESC tool? by MaxMaker1 on Thu, 2018-06-21 23:06 |
4 |
by tuloski Thu, 2018-09-13 09:36 |
VESC Tool | |
|
2 VESC 100/200 single power on switch by tobiokanobi on Wed, 2022-08-31 16:06 |
4 |
by tobiokanobi Mon, 2022-09-05 11:44 |
VESC Original Hardware | |
|
enertionboard focbox : is vesc_tool safe to use? by fourchette on Wed, 2018-11-07 23:49 |
4 |
by fourchette Tue, 2018-11-20 21:13 |
General discussion | |
|
VESC 100/250 by XBO on Tue, 2021-09-07 19:25 |
4 |
by frank Mon, 2021-09-20 14:01 |
General discussion | |
|
Control singular VESC using CAN-BUS and Arduino by Cam on Wed, 2021-01-06 10:29 |
4 |
by craiggault Wed, 2022-04-27 23:07 |
General discussion | |
|
Hub Motor Gives up while Coasting With No Faults by vadicus on Sun, 2020-08-09 01:36 |
4 |
by vadicus Tue, 2020-08-11 18:01 |
General discussion | |
|
Vesc tool not working by faheemift on Sun, 2021-02-14 14:44 |
4 |
by faheemift Wed, 2021-04-14 22:59 |
General discussion | |
|
FOC wizard confusion by Stupidspencer on Mon, 2019-07-08 04:18 |
4 |
by lurch Sun, 2021-10-24 14:46 |
VESC Tool | |
|
UAVCAN vs DroneCAN vs Cypal by AndreasSkaar on Fri, 2024-05-03 22:17 |
4 |
by Williamzoe2002 Thu, 2025-03-20 10:23 |
General discussion | |
|
VESC on 48V 1500W HUB motor by jordanlow on Sat, 2019-01-12 14:52 |
4 |
by jordanlow Thu, 2019-01-24 04:14 |
VESC Original Hardware | |
|
MOSFET failure and replacement, stormcore 60d by Airatic on Wed, 2022-01-19 11:36 |
4 |
by j.konrad Sat, 2022-01-22 01:17 |
General discussion |
Pages
