You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
Old Firmware update problem by Wormsnake on Tue, 2020-09-08 11:20 |
3 |
by jackherer Fri, 2021-04-16 16:57 |
VESC Firmware | |
|
FOCBOX X is not detected by sumedh on Tue, 2022-09-13 22:16 |
3 |
by frank Mon, 2022-09-19 09:18 |
General discussion | |
|
IMU 9250 and 6050 not working on new vesc 4.12 and 4.20 by trung_qly on Sun, 2021-09-05 16:11 |
3 |
by spatsirk Mon, 2025-06-09 18:55 |
General discussion | |
|
Reverse safety function by rich on Tue, 2017-09-05 10:14 |
3 |
by rich Wed, 2017-09-06 11:07 |
Feature Requests | |
|
Upload bootloader to stm32 f405? by jneumann on Sat, 2020-08-08 07:11 |
3 |
by TechAUmNu Sat, 2020-08-08 18:29 |
General discussion | |
|
Question on throttle response by petermarcotte1 on Wed, 2020-07-29 11:28 |
3 |
by petermarcotte1 Sat, 2020-08-01 14:17 |
General discussion | |
|
Vesc Tool with Tenka, firmware error by DankPoppin on Sun, 2023-05-28 20:39 |
3 |
by jaymacnulty Fri, 2023-07-14 07:30 |
Third Party Hardware | |
|
Fault:DRV8302 DUAL V4 by Lzx19961014 on Tue, 2018-09-04 11:48 |
3 |
by stone_1706 Sat, 2019-02-02 17:09 |
General discussion | |
|
when speed of vesc motor too fast and the arduino pin signal is unstable by HumorLogic on Tue, 2021-04-06 14:21 |
3 |
by woliam Sat, 2021-04-10 15:17 |
General discussion | |
|
VESC6+ compatible 540 1/10 BLDC motor recommendation by henry10210 on Tue, 2019-12-17 08:15 |
3 |
by benjamin Sun, 2019-12-22 09:56 |
General discussion | |
|
make and make upload okay, but no connection by martin2day on Tue, 2021-02-16 19:19 |
3 |
by CTSchorsch Wed, 2021-02-17 14:02 |
Third Party Hardware | |
|
HELP! Underpowered motor! by natebakesacake123 on Thu, 2024-02-08 04:22 |
3 |
by natebakesacake123 Thu, 2024-02-08 21:22 |
General discussion | |
|
Motor detection accuracy in 3rd party hardware (old FW vs new FW) by shaman on Tue, 2020-02-25 16:03 |
3 |
by vadicus Wed, 2020-02-26 19:09 |
Third Party Hardware | |
|
Cruise control by setting RPM over UART by solidgeek on Thu, 2018-02-15 10:56 |
3 |
by Lzx19961014 Thu, 2018-07-05 11:20 |
General discussion | |
|
VESC 4.20 Schematic by evbkez on Fri, 2019-09-20 07:59 |
3 |
by TheFallen Fri, 2019-09-27 17:45 |
General discussion | |
|
Danger to go more than 100% duty cycle during downhill ? by f.damien12 on Thu, 2022-03-24 14:12 |
3 |
by skyline1970 Sat, 2022-03-26 09:29 |
VESC Original Hardware | |
|
Powering VESC and motor from powersupply by SIGURD on Tue, 2022-12-13 13:53 |
3 |
by frank Thu, 2022-12-15 20:34 |
General discussion | |
|
Completely disabling regen current possibility on vesc by riraheta on Tue, 2022-11-29 01:48 |
3 |
by frank Wed, 2022-11-30 09:33 |
General discussion | |
|
200V +200A power stage and custom VESC controller with fault protection by ZombieSS on Sat, 2020-07-18 07:35 |
3 |
by mystamo Tue, 2020-07-28 22:07 |
Third Party Hardware | |
|
SPI Encoder communications with AS5047 by vadimz on Sun, 2018-10-28 16:55 |
3 |
by Guillaume227 Mon, 2019-02-11 23:14 |
VESC Firmware |
Pages
